Airtac SGC Standard Cylinder SGC160X35S
The AirTAC Airtac SGC Standard Cylinder SGC160X35S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø160mm bore and 35mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ160 mm
- Stroke35 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC160X35S
Delivering 10053 N of push force at 0.5 MPa, this double-acting large-bore cylinder brings serious thrust to short-stroke tasks. The SGC160X35S features a 160 mm bore and a 35 mm stroke, utilizing a robust tie-rod design where four steel rods clamp the aluminum barrel to the covers for high structural rigidity. Because it adheres to the ISO 15552 mounting interface, it drops directly into existing large-bore fixtures without alignment headaches.
The integrated -S piston magnet enables CMSG, DMSG, or EMSG switches for precise end-of-stroke detection. For practical sizing, plan for roughly 6032 N of real work at 0.5 MPa, which equates to lifting about 512 kg vertically with a 2:1 safety margin. The G3/4 port and M36x2.0 rod thread supply ample flow and strength, while the two-way piston seal maintains an internal oil reservoir for long service life.
Airtac SGC Standard Cylinder SGC160X35S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC160X35S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø160 mm |
| Stroke | 35 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø160mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 10053 N | 9425 N |
| 0.7 MPa | 14074 N | — |
| Max (@1.0 MPa) | 2050 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC160X35S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 160 | Bore size in mm (125 / 160 / 200 / 250). |
| ×35 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC160X35S Is Used
Short-Stroke Stamping
Ideal for driving heavy-duty stamping or forming dies over a tight 35 mm travel where high 10053 N thrust is required without long extension.
Pallet Halting
Acts as a rugged stopper block on high-mass conveyor lines, using its rigid tie-rod body and 9425 N pull force to arrest heavy pallets securely.
Heavy Clamping Jigs
Provides intense 0.7 MPa clamping force (14074 N) to hold thick steel or timber workpieces firmly in place during secondary machining operations.
Is the Airtac SGC Standard Cylinder SGC160X35S the Right Cylinder?
When sizing this 160 mm bore actuator, compare your actual load against its 10053 N push and 9425 N pull ratings at 0.5 MPa. If your application demands less force, stepping down to the 125 mm bore yields 6136 N of push force; conversely, moving up to the 200 mm bore provides 15708 N for heavier cycles. Because this SKU includes the -S magnet, it is fully ready for CMSG/DMSG/EMSG sensor mounting. Remember that the adjustable air cushion only decelerates the piston near the stroke end and does not function as a brake; if air pressure drops, the piston will drift, so fit an external rod lock or pilot-operated check valve for suspended loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC160X35S FAQ
This 160 mm bore cylinder features a G3/4 air port and an M36x2.0 rod thread. It generates 10053 N push and 9425 N pull at 0.5 MPa, 14074 N push and 13194 N pull at 0.7 MPa, with a theoretical maximum force of 2050 kgf at 1.0 MPa.
Yes, the -S suffix indicates a built-in piston magnet compatible with CMSG, DMSG, and EMSG switches. Additionally, its ISO 15552 mounting interface ensures dimensional interchangeability with standard large-bore fixtures, making physical replacement and bracket alignment straightforward.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC160X35S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.