Airtac SGC Standard Cylinder SGC160X750
The AirTAC Airtac SGC Standard Cylinder SGC160X750 is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø160mm bore and 750mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ160 mm
- Stroke750 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC160X750
Delivering 10053 N of push force at 0.5 MPa, this double-acting 160 mm bore cylinder handles heavy automation tasks. The G3/4 port and M36x2.0 rod thread feed a robust Ø40 mm piston rod. Four steel tie rods clamp the aluminum barrel to the covers, providing the high rigidity needed for large-bore thrust, while a two-way piston seal maintains an internal oil reservoir for long service life.
Because it uses the standardized ISO 15552 mounting interface, this model drops directly into existing large-bore fixtures and shares common accessory dimensions. Plan for about 6032 N of real work at 0.5 MPa, which means it lifts roughly 512 kg vertically with a 2:1 safety margin. The default TPU seals operate from -20 to +70 C, with a Viton H option available for 0-150 C environments. Note that this SKU lacks the -S magnet, so it cannot host CMSG, DMSG, or EMSG switches.
Airtac SGC Standard Cylinder SGC160X750 Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC160X750 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø160 mm |
| Stroke | 750 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø160mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 10053 N | 9425 N |
| 0.7 MPa | 14074 N | — |
| Max (@1.0 MPa) | 2050 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC160X750
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 160 | Bore size in mm (125 / 160 / 200 / 250). |
| ×750 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC160X750 Is Used
Press Ejection
Uses the 9425 N pull force at 0.5 MPa to extract heavy stamped metal panels from press dies.
Pallet Depalletizer
Lifts approximately 512 kg of layered goods vertically during automated pallet breakdown over its 750 mm range.
Injection Mold Clamping
Provides steady 10053 N push force at 0.5 MPa to secure mid-size mold halves during plastic injection cycles.
Is the Airtac SGC Standard Cylinder SGC160X750 the Right Cylinder?
When sizing this 160 mm bore option, verify if the 14074 N push at 0.7 MPa is required, or if stepping down to a 125 mm bore (8590 N push at 0.7 MPa) suffices. If your application demands even more power, the 200 mm bore offers 21991 N at 0.7 MPa. For this specific 750 mm stroke, external guide rails are strongly recommended to prevent rod bending and side-load damage during long extensions. Since this is a plain double-acting cylinder, the piston will drift if air is lost or the valve is centered; the adjustable 50 mm air cushions only decelerate the piston near stroke end and do not act as a brake. To hold a vertical load securely, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC160X750 FAQ
This 160 mm bore cylinder features a G3/4 air port. It delivers 10053 N push and 9425 N pull at 0.5 MPa, 14074 N push and 13194 N pull at 0.7 MPa, with a theoretical maximum of 2050 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, fitting standard LB foot, FA flange, and TC trunnion accessories. The rigid tie-rod construction handles high thrust, but this SKU lacks a magnet, so adding CMSG or DMSG sensors requires the -S variant.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC160X750
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.