Airtac SGC Standard Cylinder SGC200X1000S
The AirTAC Airtac SGC Standard Cylinder SGC200X1000S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 1000mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke1000 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X1000S
Delivering 15708 N of push force at 0.5 MPa, this large-bore double-acting actuator is built on a genuine ISO 15552 mounting interface for seamless fixture interchangeability. The four steel tie rods clamp the aluminum barrel to the covers, providing the high rigidity needed for heavy thrust, while the two-way piston seal maintains an internal oil reservoir for long service life. A built-in magnet (-S) enables direct mounting of CMSG, DMSG, or EMSG position switches.
With a 1000 mm stroke, plan for roughly 9425 N of real work at 0.5 MPa, which equates to lifting about 801 kg vertically with a 2:1 safety margin. The G3/4 port and M36x2.0 rod thread handle the high airflow and mechanical load required for such capacity. For elevated thermal demands, the standard TPU seals can be swapped for Viton H to support 0-150 C environments.
Airtac SGC Standard Cylinder SGC200X1000S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X1000S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X1000S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X1000S Is Used
Automotive Press Transfer
Drives long-stroke transfer arms in stamping lines, utilizing the 21991 N push force at 0.7 MPa to shift heavy body panels between die stations.
Palletizer Elevator
Lifts loaded pallets via a 1000 mm extension, relying on the rigid tie-rod construction to maintain alignment under high vertical dynamic forces.
Injection Mold Ejector
Provides the sustained 15079 N pull force at 0.5 MPa required to withdraw heavy molded plastic components from deep cavity tools.
Is the Airtac SGC Standard Cylinder SGC200X1000S the Right Cylinder?
When sizing this 200 mm bore unit, verify if the 160 mm bore (10053 N push @0.5 MPa) is sufficient, or if you must step up to the 250 mm bore (24543 N push @0.5 MPa) for heavier loads. Because this model features a 1000 mm stroke, external guide rails are strongly recommended to prevent rod bending and absorb side loads during long extensions. The included -S magnet allows seamless integration of CMSG, DMSG, or EMSG sensors for end-of-stroke detection.
Remember that the adjustable 50 mm air cushions only decelerate the piston near the end caps; they do not function as a brake. If the application requires the load to be held statically during air loss or valve centering, you must install an external pilot-operated check valve or a dedicated rod lock.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X1000S FAQ
This 200 mm bore cylinder features a G3/4 air port and an M36x2.0 rod thread. It generates 15708 N push and 15079 N pull at 0.5 MPa, 21991 N push and 21110 N pull at 0.7 MPa, with a theoretical maximum of 3204 kgf at 1.0 MPa.
No, the adjustable 50 mm air cushions only decelerate the piston near the stroke ends and cannot hold a load. If static holding is required during air loss or valve centering, an external rod lock or pilot-operated check valve must be installed.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X1000S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.