Airtac SGC Standard Cylinder SGC200X1300
The AirTAC Airtac SGC Standard Cylinder SGC200X1300 is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 1300mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke1300 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X1300
Delivering 15708 N of push force at 0.5 MPa, this large-bore ISO 15552 tie-rod cylinder is built for heavy-duty automation. Four steel tie rods clamp the aluminium barrel to the covers for high rigidity, while the two-way piston seal maintains an internal oil reservoir for long service life. Plan for about 9425 N of real work at 0.5 MPa, which safely lifts roughly 801 kg vertically with a 2:1 margin.
The Ø200 mm bore uses a G3/4 air port and a 50 mm adjustable air cushion at both ends to decelerate the payload smoothly. Because this specific SKU lacks the -S magnet option, it cannot accept CMSG, DMSG, or EMSG magnetic switches. The standard TPU seals handle temperatures from -20 to +70 C, with a Viton H option available for environments up to 150 C.
Airtac SGC Standard Cylinder SGC200X1300 Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X1300 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 1300 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X1300
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×1300 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X1300 Is Used
Press Ejection Systems
Provides the long 1300 mm reach and 21991 N push force at 0.7 MPa needed to clear large stamped parts from heavy press beds.
Pallet Transfer Stops
Acts as a high-force stopper mechanism on wide assembly lines, using its robust tie-rod build to absorb repeated impacts from fully loaded pallets.
Vertical Lift Doors
Raises heavy industrial rolling doors or material handling gates, where the 801 kg vertical lift capacity matches substantial counterweight requirements.
Is the Airtac SGC Standard Cylinder SGC200X1300 the Right Cylinder?
When sizing this 1300 mm stroke model, compare it against the adjacent SGC bores: the smaller Ø160 bore yields 10053 N of push at 0.5 MPa, while the larger Ø250 bore provides 24543 N. At this extreme length, adding external guide rails is critical to prevent rod bending and side-load damage under heavy thrust. Note that an unpowered SGC cylinder will drift if air is lost or the valve is centered; the air cushion only decelerates the piston near the stroke end and does not function as a locking brake. For suspended or vertical loads, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X1300 FAQ
The Ø200 mm bore features a G3/4 air port and generates 15708 N push / 15079 N pull at 0.5 MPa, 21991 N push / 21110 N pull at 0.7 MPa, and a theoretical maximum of 3204 kgf at 1.0 MPa.
Yes, the SGC series is dimensionally interchangeable per the ISO 15552 mounting interface, allowing it to drop into the same foot, flange, or trunnion fixtures as other standard large-bore cylinders.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X1300
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.