Airtac SGC Standard Cylinder SGC200X50
The AirTAC Airtac SGC Standard Cylinder SGC200X50 is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 50mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke50 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X50
Delivering 15708 N of push force at 0.5 MPa, this double-acting large-bore cylinder is built for heavy-duty automation. The Ø200 mm bore operates on a G3/4 air port, with a Ø40 mm hard-chrome rod and M36x2.0 thread. Four steel tie rods clamp the aluminium barrel to the covers, providing high rigidity under large thrust loads, while the two-way piston seal maintains an internal oil reservoir for long service life.
Because it follows the standardized ISO 15552 mounting interface, it drops directly into existing large-bore fixtures and accessory kits. Plan for about 9425 N of real work at 0.5 MPa, which equates to lifting roughly 801 kg vertically with a 2:1 safety margin. Note that this specific SKU lacks the -S magnet, so it cannot host CMSG, DMSG, or EMSG position switches.
Airtac SGC Standard Cylinder SGC200X50 Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X50 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 50 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X50
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×50 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X50 Is Used
Stamping Press Feed
Pushes heavy coil stock into a mechanical press with 15708 N of force, utilizing the short 50 mm stroke for rapid indexing.
Pallet Stopper Gate
Acts as a high-force physical stop barrier on heavy-duty pallet conveyors, absorbing impact via the 50 mm cushioned stroke.
Injection Mold Clamp
Secures heavy injection molding tooling halves using the rigid four tie-rod construction and 3204 kgf maximum theoretical force.
Is the Airtac SGC Standard Cylinder SGC200X50 the Right Cylinder?
When sizing this 200 mm bore actuator, compare its 15708 N push force at 0.5 MPa against the smaller Ø160 bore (10053 N) or the larger Ø250 bore (24543 N) to match your exact load. The 50 mm stroke provides rapid, short-travel actuation without the rod-bending side-load risks seen on longer 500 mm+ strokes. Because this SKU has no -S magnet, you must choose an external mechanical limit switch if sensing is required. Furthermore, standard air cushions only decelerate the piston near the end caps; they do not function as a lock. If the machine loses air, the piston will drift, so add an external rod lock or pilot-operated check valve for suspended loads.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X50 FAQ
The Ø200 mm bore features a G3/4 air port and delivers 15708 N push / 15079 N pull at 0.5 MPa, and 21991 N push / 21110 N pull at 0.7 MPa. The theoretical maximum force is 3204 kgf at 1.0 MPa.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, fitting standard LB, FA, FB, CA, CB, and TC mounts. The rigid tie-rod build handles high thrust, but this non-S SKU cannot take magnetic sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X50
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.