Airtac SGC Standard Cylinder SGC200X580S
The AirTAC Airtac SGC Standard Cylinder SGC200X580S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 580mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke580 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X580S
Delivering 15708 N of push force at 0.5 MPa, this large-bore ISO 15552 tie-rod cylinder handles heavy-duty automation with ease. Four steel tie rods clamp the aluminum barrel to the covers for high structural rigidity, while the two-way piston seal maintains an internal oil reservoir for long service life. Plan for about 9425 N of real work, or roughly 801 kg lifted vertically with a 2:1 safety margin.
Because this SKU includes the -S magnet, it supports CMSG, DMSG, and EMSG position switches for electronic or reed-sensor feedback. The G3/4 air port and M36x2.0 piston rod thread are fixed by the 200 mm bore. Standard TPU seals operate from -20 to +70 C, with Viton H available for 0-150 C high-temperature environments.
Airtac SGC Standard Cylinder SGC200X580S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X580S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 580 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X580S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×580 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X580S Is Used
Automotive Press Transfer
Moves heavy stamped body panels between die stations using the 15708 N push force, relying on the 580 mm stroke to span wide press gaps.
Pallet Diverting Arm
Actuates a heavy steel deflector plate to redirect large pallets on a high-speed packaging line, utilizing the CMSG sensor feedback for precise timing.
Vertical Lift Gate
Raises a 600 kg industrial safety gate by leveraging the 801 kg vertical lift capacity, requiring external guides to stabilize the 580 mm extension.
Is the Airtac SGC Standard Cylinder SGC200X580S the Right Cylinder?
When sizing this 200 mm bore actuator, compare it against the 160 mm bore (10053 N push at 0.5 MPa) for lighter loads, or step up to the 250 mm bore (24543 N push) if your application demands even greater thrust. The 580 mm stroke requires careful alignment to prevent rod bending; use external guide rails to support the load and minimize side-load stress on the piston rod.
The adjustable 50 mm air cushions at both ends decelerate the piston near stroke end but do not function as a lock. If the load must be held vertically when air pressure drops or the valve is centered, install an external rod lock or a pilot-operated check valve to prevent drifting.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X580S FAQ
The 200 mm bore generates 15708 N push and 15079 N pull at 0.5 MPa, 21991 N push and 21110 N pull at 0.7 MPa, with a theoretical maximum of 3204 kgf at 1.0 MPa. The air port size is G3/4.
Yes, it is dimensionally interchangeable per the ISO 15552 mounting interface, dropping directly into standard large-bore foot, flange, or trunnion fixtures. The tie-rod construction adds rigidity for high-thrust applications.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X580S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.