Airtac SGC Standard Cylinder SGC200X610
The AirTAC Airtac SGC Standard Cylinder SGC200X610 is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø200mm bore and 610mm stroke, G3/4 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ200 mm
- Stroke610 mm
- Port sizeG3/4
- Acting typeDouble acting
- Rod threadM36×2.0
- CushionAdjustable, 50 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC200X610
Delivering 15708 N of push force at 0.5 MPa, this double-acting large-bore cylinder is built around a genuine ISO 15552 tie-rod format. Four steel tie rods clamp the aluminum barrel to the front and rear covers, providing the high rigidity needed to handle massive thrust without flexing. The two-way piston seal incorporates an oil reservoir function to maintain continuous lubrication for a long service life.
With a 610 mm stroke and a G3/4 air port, it is designed for substantial travel tasks. For practical sizing, plan for about 9425 N of real work at 0.5 MPa, which equates to lifting roughly 801 kg vertically with a 2:1 safety margin. Note that this specific SKU lacks a magnet, so it cannot host CMSG, DMSG, or EMSG magnetic switches without upgrading to the -S variant.
Airtac SGC Standard Cylinder SGC200X610 Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC200X610 |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø200 mm |
| Stroke | 610 mm |
| Acting type | Double acting |
| Port size | G3/4 |
| Rod thread | M36×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 50 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø200mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 15708 N | 15080 N |
| 0.7 MPa | 21991 N | — |
| Max (@1.0 MPa) | 3204 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC200X610
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 200 | Bore size in mm (125 / 160 / 200 / 250). |
| ×610 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC200X610 Is Used
Automotive Press Stamping
Drives heavy forming dies over 610 mm to shape vehicle body panels, utilizing the 21991 N push force at 0.7 MPa to ensure crisp metal deformation.
Pallet Dispenser Mechanism
Pushes empty or loaded pallets out of a vertical magazine, easily handling the 801 kg safe vertical lift capacity calculated at 0.5 MPa.
Heavy Waste Compaction
Crushes industrial scrap and packaging material in a 610 mm stroke cycle, relying on the rigid four-rod construction to maintain alignment under off-center loads.
Is the Airtac SGC Standard Cylinder SGC200X610 the Right Cylinder?
When sizing this 200 mm bore actuator, compare it against its neighbors: the 160 mm bore yields 10053 N of push at 0.5 MPa, while the 250 mm bore provides 24543 N. Choose this 200 mm option when the 160 mm class is insufficient but you want to avoid the heavier mass and larger footprint of the 250 mm unit. Because the 610 mm stroke creates a long lever arm, external guide rails are strongly recommended to prevent rod bending under heavy side loads.
Keep in mind that a standard double-acting cylinder drifts when air pressure is lost or the valve is centered, as the end-of-stroke air cushions only decelerate the piston and do not act as a brake. To suspend a load safely mid-stroke, integrate an external pilot-operated check valve or a dedicated rod lock.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC200X610 FAQ
The 200 mm bore features a G3/4 air port and an M36x2.0 rod thread. It delivers 15708 N push and 15079 N pull at 0.5 MPa, 21991 N push and 21110 N pull at 0.7 MPa, with a theoretical maximum force of 3204 kgf at 1.0 MPa.
No, this specific SKU does not include a piston magnet, meaning it cannot support CMSG, DMSG, or EMSG magnetic switches. You must select the -S magnet option to enable magnetic sensing, though you can still mount mechanical limit switches externally.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC200X610
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.