Airtac SGC Standard Cylinder SGC250X1000S
The AirTAC Airtac SGC Standard Cylinder SGC250X1000S is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø250mm bore and 1000mm stroke, G1 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ250 mm
- Stroke1000 mm
- Port sizeG1
- Acting typeDouble acting
- Rod threadM42×2.0
- CushionAdjustable, 60 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC250X1000S
Delivering 24543 N of push force at 0.5 MPa, this double-acting ISO 15552 tie-rod cylinder is built for heavy-duty automation. Four steel tie rods clamp the aluminum barrel to the covers, ensuring high rigidity under large-bore thrust, while the two-way piston seal maintains an internal oil reservoir for long service life. Because this is a Ø250 bore, TPU seals are not available; instead, the front-cover packing and buffer gasket are NBR, with a Viton H option for 0-150 C high-temperature environments.
Equipped with a built-in piston magnet (-S), the unit supports CMSG, DMSG, and EMSG switches for position sensing. It features a 50 mm piston rod, a G1 air port, and an M42x2.0 rod-end thread. For practical sizing, plan for about 14726 N of real work at 0.5 MPa, which safely lifts roughly 1251 kg vertically with a 2:1 margin.
Airtac SGC Standard Cylinder SGC250X1000S Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC250X1000S |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø250 mm |
| Stroke | 1000 mm |
| Acting type | Double acting |
| Port size | G1 |
| Rod thread | M42×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 60 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø250mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 24544 N | 23562 N |
| 0.7 MPa | 34361 N | — |
| Max (@1.0 MPa) | 5006 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC250X1000S
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 250 | Bore size in mm (125 / 160 / 200 / 250). |
| ×1000 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC250X1000S Is Used
Heavy Press Stamping
Provides the 24543 N push at 0.5 MPa required to form thick-gauge steel plates in automated mechanical press lines.
Palletizer Elevation
Raises full 1251 kg unit loads through a 1000 mm vertical cycle, relying on external guides to stabilize the extended rod.
Injection Mold Actuation
Shifts heavy mold halves with 34360 N thrust at 0.7 MPa, using the -S magnet to trigger CMSG reed switches at stroke ends.
Is the Airtac SGC Standard Cylinder SGC250X1000S the Right Cylinder?
When sizing this 1000 mm stroke model, consider the adjacent bores in the SGC family: the Ø200 provides 15708 N push at 0.5 MPa, while the Ø250 is the largest available, offering a maximum theoretical force of 5006 kgf at 1.0 MPa. At this long 1000 mm extension, large-bore side loads can induce rod bending, so external guide rails or rod-end support are strongly recommended to prevent premature seal wear.
This SKU includes the -S magnet for direct sensor mounting. Note that a standard cylinder drifts when air is lost or the valve is centered; the adjustable 60 mm air cushions only decelerate the piston near stroke end. To suspend a load safely, install an external rod lock or a pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC250X1000S FAQ
This Ø250 bore model features a G1 air port and generates 24543 N push / 23562 N pull at 0.5 MPa, 34360 N push / 32986 N pull at 0.7 MPa, and a theoretical maximum of 5006 kgf at 1.0 MPa.
The -S magnet allows CMSG, DMSG, and EMSG switches for position detection, but the cylinder cannot hold a load unpowered; an external rod lock is needed. Its ISO 15552 mounting interface ensures dimensional interchangeability with standard large-bore fixtures.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC250X1000S
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.