Airtac SGC Standard Cylinder SGC250X600H
The AirTAC Airtac SGC Standard Cylinder SGC250X600H is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø250mm bore and 600mm stroke, G1 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ250 mm
- Stroke600 mm
- Port sizeG1
- Acting typeDouble acting
- Rod threadM42×2.0
- CushionAdjustable, 60 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC250X600H
Delivering massive thrust for heavy industry, this double-acting large-bore cylinder pushes with 24543 N and pulls with 23562 N at 0.5 MPa. Built on a genuine ISO 15552 mounting interface, it drops directly into existing large-bore fixtures without custom bracketry. Four steel tie rods clamp the aluminium barrel to the covers, providing the high rigidity needed to handle these extreme forces, while a two-way piston seal maintains an internal oil reservoir for long service life.
Because this specific SKU carries the H designation, it uses Viton FKM seals rated for 0-150 C high-temperature environments instead of standard TPU (which is not offered on the 250 bore). Plan for roughly 14726 N of real work at 0.5 MPa, which equates to lifting about 1251 kg vertically with a 2:1 safety margin. The G1 air port, M42x2.0 rod thread, and 60 mm adjustable air cushions at both ends manage the pneumatic flow for smooth operation across the 600 mm travel.
Airtac SGC Standard Cylinder SGC250X600H Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC250X600H |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø250 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1 |
| Rod thread | M42×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 60 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø250mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 24544 N | 23562 N |
| 0.7 MPa | 34361 N | — |
| Max (@1.0 MPa) | 5006 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC250X600H
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 250 | Bore size in mm (125 / 160 / 200 / 250). |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC250X600H Is Used
Automotive Press Tending
Handles heavy stamping blanks and moves large dies into hydraulic presses, utilising the 24543 N push force to shift substantial mass in high-heat environments.
Foundry Mould Handling
Leverages the Viton H high-temperature seals to operate reliably near hot casting lines, shifting heavy sand moulds across the 600 mm stroke without degrading.
Palletiser Head Actuator
Drives the main lifting carriage for heavy unit loads, moving approximately 1251 kg of palletised goods vertically with a safe 2:1 working margin.
Is the Airtac SGC Standard Cylinder SGC250X600H the Right Cylinder?
When sizing this 250 mm bore unit, compare your actual load against its 34360 N push force at 0.7 MPa. If your application is lighter, the next size down is the 200 bore delivering 15708 N at 0.5 MPa; as 250 is the largest in the SGC series, exceeding this capacity requires multiple cylinders or a different mechanism. Note that this specific model lacks the -S magnet, meaning it cannot accept CMSG, DMSG, or EMSG magnetic switches for position sensing—you will need external mechanical limit switches. Furthermore, because this is a 600 mm stroke, the extended 50 mm rod is highly susceptible to bending under lateral stress; always use an external guide or stopper to prevent side-loading and premature seal failure. Finally, remember the air cushions only decelerate the piston near the stroke ends and do not act as a brake; if the air supply drops, the piston will drift, so fit an external rod lock or pilot-operated check valve to suspend loads safely.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC250X600H FAQ
At 0.5 MPa it pushes with 24543 N and pulls with 23562 N. At 0.7 MPa the push is 34360 N and the pull is 32986 N, with a theoretical maximum of 5006 kgf at 1.0 MPa. It features a 250 mm bore, a 600 mm stroke, a G1 air port, an M42x2.0 rod thread, and 60 mm adjustable air cushions at both ends.
No, this specific SKU lacks the -S magnet, so it cannot host CMSG, DMSG, or EMSG switches; you must use external mechanical limit switches. However, the H designation means it is equipped with Viton FKM seals, allowing operation in environments up to 150 C. It is built with a genuine ISO 15552 tie-rod mounting interface for easy fixture integration.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC250X600H
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.