Airtac SGC Standard Cylinder SGC250X600TC
The AirTAC Airtac SGC Standard Cylinder SGC250X600TC is a genuine double acting ISO 15552 (orig. ISO 6431) tie-rod air cylinder with a Ø250mm bore and 600mm stroke, G1 air ports and adjustable end cushioning. Its large-bore tie-rod build delivers high thrust and drops into standardized ISO 15552 mounting on heavy automation.
- BoreØ250 mm
- Stroke600 mm
- Port sizeG1
- Acting typeDouble acting
- Rod threadM42×2.0
- CushionAdjustable, 60 mm
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac SGC Standard Cylinder SGC250X600TC
Delivering massive thrust for heavy industry, this double-acting tie-rod cylinder pushes with 24543 N and pulls with 23562 N at 0.5 MPa. Four steel tie rods clamp the aluminium barrel to the covers for extreme rigidity under high stress, while the two-way piston seal maintains an internal oil reservoir for long service life. Because it carries the standardized ISO 15552 mounting interface, it drops directly into existing large-bore fixtures without custom bracketry.
For real-world sizing, plan for about 14726 N of actual work at 0.5 MPa, which safely lifts roughly 1251 kg vertically with a 2:1 margin. The Ø250 bore uses a G1 air port and an M42x2.0 rod thread. Note that TPU seals are unavailable for this bore; the front-cover packing and buffer gasket are NBR, with a Viton H option for 0-150 C high-temperature environments.
Airtac SGC Standard Cylinder SGC250X600TC Technical Specifications
| Model | Airtac SGC Standard Cylinder SGC250X600TC |
|---|---|
| Series | SGC ISO 15552 tie-rod cylinder |
| Bore size | Ø250 mm |
| Stroke | 600 mm |
| Acting type | Double acting |
| Port size | G1 |
| Rod thread | M42×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable, 60 mm |
| Max standard stroke | Up to 1500 mm |
Specifications follow the official AirTAC SGC datasheet and ISO 15552 dimensions. Confirm against the product label before installation. Thread options: PT (blank) / G. TPU seals are not available for the Ø250 bore (NBR / Viton only).
Theoretical Output Force (Ø250mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 24544 N | 23562 N |
| 0.7 MPa | 34361 N | — |
| Max (@1.0 MPa) | 5006 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac SGC Standard Cylinder SGC250X600TC
| SGC | ISO 15552 tie-rod cylinder (double-acting type). |
|---|---|
| 250 | Bore size in mm (125 / 160 / 200 / 250). |
| ×600 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
SGC-family variants: SGC (double acting), SGCD (double rod), SGCJ (adjustable stroke). Mounting: LB / FA / FB / CA / CB / CR / TC / FTC / TCM1 / TCM2. Seals: TPU (blank) / Viton H / NBR N.
Where the Airtac SGC Standard Cylinder SGC250X600TC Is Used
Heavy Press Stamping
Drives large press dies requiring 24543 N of push force at 0.5 MPa to form thick steel plates.
Pallet Upender
Pivots on the TC trunnion to rotate heavy pallet loads up to 1251 kg vertically through a 600 mm arc.
Injection Mold Clamp
Secures large injection molding halves, using the NBR buffer gasket to absorb 34360 N peak impacts at 0.7 MPa.
Is the Airtac SGC Standard Cylinder SGC250X600TC the Right Cylinder?
This 250 mm bore sits at the top of the SGC range, so if 24543 N of push at 0.5 MPa is excessive, step down to the 200 mm bore (15708 N push). There is no larger standard SGC option for higher demands. The TC trunnion mount suits pivoting loads, but because this is a 600 mm stroke, you must use external guides to prevent rod bending and side-load damage. As a standard SKU without the -S magnet, it cannot accept CMSG, DMSG, or EMSG position switches; order the -S variant if sensing is required. Finally, the end cushions only decelerate the piston near stroke end and will not hold a load if air pressure drops—install an external rod lock or pilot-operated check valve for vertical safety.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G / NPT)
- ✓ Magnet (-S) for sensors?
- ✓ Long-stroke side load — support the rod end
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load; support long strokes at the rod end.
- check Set cushions to minimum, then release gradually.
- check Use correct mounting accessory (LB/FA/FB/CA/CB/CR/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac SGC Standard Cylinder SGC250X600TC FAQ
This 250 mm bore cylinder features a G1 air port and delivers 24543 N push / 23562 N pull at 0.5 MPa, and 34360 N push / 32986 N pull at 0.7 MPa. The theoretical maximum force is 5006 kgf at 1.0 MPa.
This specific SKU lacks the -S magnet, so it cannot accept CMSG, DMSG, or EMSG switches. The four steel tie-rod construction provides high rigidity while remaining dimensionally interchangeable per the ISO 15552 mounting interface for standard TC trunnion, foot, and flange accessories.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Made to Order
Large-bore cylinders built to order — confirm lead time.
Fast Reply
Most inquiries answered within 7-8 hours.
Related AirTAC SGC Cylinders
Request a Quote for Airtac SGC Standard Cylinder SGC250X600TC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.