Airtac MIC Cushioned Mini Cylinder MIC16X225CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC16X225CA is a genuine double acting + cushion round-body mini air cylinder with a Ø16mm bore and 225mm stroke, M5×0.8 air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ16 mm
- Stroke225 mm
- Port sizeM5×0.8
- Acting typeDouble acting + cushion
- Rod threadM6×1.0
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC16X225CA
Designed for high-speed actuation, the AirTAC MIC16X225CA is a double-acting, round-body stainless steel mini cylinder featuring a 225 mm stroke and a CA rear pivot cover. A variable air cushion at both ends lets you dial in the deceleration needle to absorb end-of-stroke shock, protecting your payload while reducing noise. The stainless barrel and rod resist mild corrosion and washdown environments.
Delivering 100.5 N of push force at 0.5 MPa, this unit provides a safe working load of roughly 60 N and lifts about 5.1 kg vertically with a 2:1 safety margin. It uses an M5×0.8 port and an M6x1.0 male rod thread. Conforming to the ISO 6432 mounting interface for Ø16 bores, it drops directly into standard mini brackets. Note this SKU lacks a magnet, so it cannot accept CMSG, DMSG, or EMSG sensors.
Airtac MIC Cushioned Mini Cylinder MIC16X225CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC16X225CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø16 mm |
| Stroke | 225 mm |
| Acting type | Double acting + cushion |
| Port size | M5×0.8 |
| Rod thread | M6×1.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø16mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 101 N | 86 N |
| 0.7 MPa | 141 N | 121 N |
| Max (@1.0 MPa) | 21 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC16X225CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 16 | Bore size in mm. |
| ×225 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC16X225CA Is Used
Light Parts Ejector
Throws small plastic parts out of a molding area at high speed, using the adjustable cushion to stop the 225 mm travel softly without slamming the end cap.
Package Deflector
Pushes light cartons off a sorting line with a safe working load of 60 N, relying on the stainless build to endure occasional washdowns.
Lab Sample Shuttle
Moves delicate test tubes between stations where the 5.1 kg vertical lift capacity and needle-set deceleration prevent liquid spills and glass breakage.
Is the Airtac MIC Cushioned Mini Cylinder MIC16X225CA the Right Cylinder?
When sizing this 16 mm bore, stepping down is not an option for cushioned models, as the smaller Ø8/10/12 sizes are bumper-only MI variants. Stepping up to the MIC20X50 yields 157.0 N of push force at 0.5 MPa if you need to move heavier loads. The adjustable cushion is essential when cycling at high speeds or moving sensitive masses, as it prevents harsh impacts. Remember that the cushion only decelerates the piston near the stroke end; it does not lock or hold the load. If air pressure drops, the rod will drift, so fit an external rod lock or pilot check valve for position holding.
The CA back cover provides a rear pivot point for clevis mounting. Because this specific SKU is built without a magnet, it cannot support position sensing. To use CMSG, DMSG, or EMSG switches, you must select the -S magnet variant.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC16X225CA FAQ
This 16 mm bore cylinder uses an M5×0.8 port and an M6x1.0 male rod thread. It generates 100.5 N push and 86.4 N pull at 0.5 MPa, 140.7 N push and 120.9 N pull at 0.7 MPa, with a theoretical maximum force of 20.5 kgf at 1.0 MPa.
No, this specific SKU does not include a magnet and cannot accept CMSG, DMSG, or EMSG switches. You must order the -S variant for position sensing. The adjustable air cushion at both ends only serves to decelerate the load near stroke end and does not act as a brake.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC16X225CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.