Airtac MIC Cushioned Mini Cylinder MIC20X10CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC20X10CA is a genuine double acting + cushion round-body mini air cylinder with a Ø20mm bore and 10mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ20 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM8×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC20X10CA
Built as a double-acting, round-body stainless steel mini cylinder, the MIC20X10CA uses an adjustable air cushion at both ends to decelerate loads smoothly. The stainless barrel and rod resist mild corrosion, making it suitable for washdown environments. Delivering 157 N of push force at 0.5 MPa, it handles a safe working load of roughly 94 N, lifting about 8 kg vertically with a 2:1 margin.
This 20 mm bore unit features a 1/8 inch port and an M8x1.25 male rod thread. It uses the ISO 6432 mounting interface for standard mini-cylinder brackets. The CA rear pivot cover allows direct clevis mounting. Note that this specific SKU lacks a magnet and cannot support CMSG, DMSG, or EMSG sensors; order the -S variant for position sensing.
Airtac MIC Cushioned Mini Cylinder MIC20X10CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC20X10CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø20 mm |
| Stroke | 10 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | 185 N |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC20X10CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 20 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC20X10CA Is Used
Package Diverter
Snaps a lightweight routing gate at high speed, relying on the adjustable cushion to prevent end-of-stroke slamming on the 10 mm stroke.
Small Part Clamp
Clamps delicate plastic components with a 94 N safe working load, while the stainless build tolerates occasional coolant spray.
Film Cut-off
Actuates a sealing jaw rapidly; the needle-set cushion absorbs the shock of the abrupt 10 mm motion to protect the blade assembly.
Is the Airtac MIC Cushioned Mini Cylinder MIC20X10CA the Right Cylinder?
For lower force needs, the MIC16 bore provides 100.5 N push at 0.5 MPa, while stepping up to the MIC25 yields 245.3 N. The adjustable cushion matters most at high speeds or when moving heavier masses, as the needle valve tunes end-of-stroke deceleration to cut shock. This cushion only slows the piston near stroke end; it does not act as a brake. To hold a load on air loss, install an external rod lock or pilot check valve. Mounting options include LB foot, FA flange, and TC trunnion, alongside the CA pivot cover.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC20X10CA FAQ
This 20 mm bore cylinder has a 1/8 inch port. It generates 157 N push and 131.9 N pull at 0.5 MPa, or 219.8 N push and 184.7 N pull at 0.7 MPa. The theoretical maximum force is 32 kgf at 1.0 MPa.
No, this SKU does not include a magnet and cannot accept CMSG, DMSG, or EMSG switches. You must order the -S variant for sensing. The adjustable air cushion only decelerates the load and does not lock or hold position on air loss.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC20X10CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.