Airtac MIC Cushioned Mini Cylinder MIC20X75SU
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC20X75SU is a genuine double acting + cushion round-body mini air cylinder with a Ø20mm bore and 75mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ20 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM8×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC20X75SU
Dial in end-of-stroke deceleration with the AirTAC MIC20X75SU, a 20 mm bore double-acting mini cylinder built around a stainless steel round barrel and rod. Instead of a fixed bumper, it uses a variable air cushion at both ends: you set the needle to absorb high-speed shock, protecting the payload and dropping noise. The U-type back cover provides a 90-degree port and mounting orientation, while the 1/8" port feeds the 8 mm piston rod.
At 0.5 MPa this bore pushes 157 N and pulls 131.9 N, peaking at a theoretical 32 kgf at 1.0 MPa. That translates to a safe working load of roughly 94 N, or about 8 kg of vertical lift with a 2:1 safety margin. Because this is an ISO 6432 mounting interface size, it drops cleanly into standard mini-cylinder brackets. The -S suffix means a piston magnet is present, ready for CMSG, DMSG or EMSG switches.
Airtac MIC Cushioned Mini Cylinder MIC20X75SU Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC20X75SU |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø20 mm |
| Stroke | 75 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M8×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø20mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 157 N | 132 N |
| 0.7 MPa | 220 N | 185 N |
| Max (@1.0 MPa) | 32 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC20X75SU
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 20 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC20X75SU Is Used
Package Diverter
Snaps small cartons off a main belt at speed; the adjustable cushion softens the 75 mm stroke stop to protect lightweight packaging.
Small Part Ejector
Kicks machined components out of a fixture; the 157 N push clears the part while the stainless rod shrugs off cutting fluid mist.
Vertical Lift Stop
Raises an 8 kg tote to a lower conveyor tier; the needle-set end cushion prevents the load from slamming at the top of travel.
Is the Airtac MIC Cushioned Mini Cylinder MIC20X75SU the Right Cylinder?
If 157 N of push at 0.5 MPa is too much, dropping to the MIC16 cuts force to 100.5 N; stepping up to the MIC25 raises it to 245.3 N. The adjustable cushion matters most when you are cycling near the 800 mm/s limit or moving a heavy load, where smoothing the stop prevents damage. Remember the cushion only decelerates the stroke end—it is not a brake. If the rod must hold position on air loss, fit an external rod lock or pilot check valve. Match your mounting using LB foot, FA flange, TC trunnion or the U back cover, and use CMSG/DMSG/EMSG sensors since the -S magnet is included.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC20X75SU FAQ
This 20 mm bore cylinder has a 1/8" port and an 8 mm rod. It pushes 157 N and pulls 131.9 N at 0.5 MPa. At 0.7 MPa it pushes 219.8 N and pulls 184.7 N. The theoretical maximum force is 32 kgf at 1.0 MPa.
Yes, the -S suffix means a magnet is built in for CMSG, DMSG or EMSG switches. The variable air cushion at both ends only decelerates the load near stroke end to reduce shock; it does not lock or hold the rod. For position holding on air loss, use an external rod lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC20X75SU
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.