Airtac MIC Cushioned Mini Cylinder MIC25X10U
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X10U is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 10mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X10U
Dial in end-of-stroke deceleration with the AirTAC MIC25X10U, a double-acting round-body mini cylinder built around a needle-set variable air cushion at both ends. The stainless steel rolled barrel and Ø10 mm piston rod shrug off mild washdown environments while smoothing out high-speed 30-800 mm/s cycles. A 90-degree U back cover configures the port and mount orientation for tight spaces.
In the Ø25 class this actuator pushes with 245.3 N and pulls with 206.1 N at 0.5 MPa, peaking at a 50 kgf theoretical maximum at 1.0 MPa. That translates to a safe working load of roughly 147 N, letting you lift about 12.5 kg vertically with a 2:1 safety margin. It uses a 1/8" port and conforms to ISO 6432 mounting dimensions for standard mini brackets. Note this SKU lacks a magnet, so it cannot host CMSG or DMSG switches without upgrading to the -S variant.
Airtac MIC Cushioned Mini Cylinder MIC25X10U Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X10U |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 10 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X10U
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X10U Is Used
Short-Stroke Clamping
Ideal for gripping heavier billets in tight fixtures, using the 245.3 N push force to secure parts without overshocking the jaw mechanism.
Flap Deflection
Rapidly tucks carton flaps on packaging lines where the adjustable air cushion silently absorbs the 10 mm impact without jarring the conveyor frame.
Vertical Press-Down
Presses lightweight labels or stamps onto components, safely handling the 12.5 kg vertical lift margin while the U cover eases port routing.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X10U the Right Cylinder?
When sizing this 10 mm stroke unit against adjacent bores, the Ø20 MIC delivers 157 N of push at 0.5 MPa, while the larger Ø32 steps up to 402 N if your payload exceeds the 147 N safe working load. The adjustable cushion is essential for heavy or fast-moving tooling, but remember it only decelerates near the stroke end. It will not lock the rod or hold position on air loss; for suspended loads add an external rod lock or pilot check valve.
Mounting options include LB foot, FA flange, SDB pivot, and TC trunnion brackets. Because this specific model has no internal magnet, position sensing is impossible unless you switch to the -S magnet version to accept CMSG, DMSG, or EMSG sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X10U FAQ
This Ø25 mm bore cylinder uses a 1/8" port and an M10x1.25 male rod thread. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, increasing to 343.4 N push and 288.5 N pull at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa.
No, this specific SKU does not include a magnet and cannot accept CMSG, DMSG, or EMSG switches. You must select the -S variant for position sensing. The stainless build and adjustable needle cushions function identically across both versions.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X10U
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.