Airtac MIC Cushioned Mini Cylinder MIC25X110U
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X110U is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 110mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke110 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X110U
Dial in end-of-stroke deceleration with the AirTAC MIC25X110U, a double-acting round-body mini cylinder built with a stainless-steel barrel and rod for mild washdown resistance. A needle-set variable air cushion at both ends absorbs high-speed shock, protecting your payload and cutting noise far better than a fixed bumper. The U rear cover provides a 90-degree port orientation to simplify plumbing in tight spaces.
Delivering 245.3 N of push force and 206.1 N of pull force at 0.5 MPa, this Ø25 bore unit uses a 1/8" port and an M10x1.25 male rod thread. It yields a safe working load of roughly 147 N, lifting about 12.5 kg vertically with a 2:1 safety margin. It conforms to the ISO 6432 mounting interface for standard mini brackets. Note this SKU lacks a magnet, so it cannot accept CMSG, DMSG, or EMSG sensors without specifying the -S variant.
Airtac MIC Cushioned Mini Cylinder MIC25X110U Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X110U |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 110 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X110U
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X110U Is Used
Package Diverting
Handles 12 kg cartons at high cycle rates on a sorting line, using the adjustable cushion to prevent harsh slams when extending the 110 mm stroke.
Flap Folding
Drives a folding arm on a case erector where the 245 N thrust tucks heavy cardboard flaps, relying on the stainless rod for mild washdown resistance.
Light Pressing
Applies steady downward pressure to seat small bearings or clips, benefiting from the smooth needle-set deceleration to avoid marking the part.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X110U the Right Cylinder?
When sizing this 245.3 N push class, step down to the MIC20 (157.0 N @0.5 MPa) for lighter loads, or move up to the MIC32 (402.2 N @0.5 MPa) if you need more thrust. The adjustable cushion shines at high speeds or when moving heavier masses, letting you tune the deceleration curve. Remember the cushion only slows the piston near stroke end; it is not a brake. If you must prevent drift on air loss, fit an external rod lock or pilot check valve. Mount via LB foot, FA flange, or TC trunnion, and choose the -S magnet version if position sensing is required.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X110U FAQ
At 0.5 MPa it pushes 245.3 N and pulls 206.1 N. At 0.7 MPa it pushes 343.4 N and pulls 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa. This bore uses a 1/8" air port and a 10 mm piston rod with an M10x1.25 male thread.
No, this specific SKU does not include a magnet, so it cannot accept CMSG, DMSG, or EMSG switches. You must order the -S variant for position sensing. The stainless-steel round-body build and adjustable air cushions at both ends function identically across both versions.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X110U
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.