Airtac MIC Cushioned Mini Cylinder MIC25X15CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X15CA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 15mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke15 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X15CA
Delivering 245.3 N of push force at 0.5 MPa, this double-acting stainless steel round-body mini cylinder is built for high-speed actuation. The MIC25X15CA features an adjustable air cushion at both ends, letting you dial in a needle valve to absorb end-of-stroke shock and reduce noise far better than a fixed bumper. Its 25 mm bore uses a 1/8" port and a 10 mm piston rod with an M10x1.25 male thread.
The stainless barrel and rod resist mild corrosion and washdown environments. Because this bore falls within the Ø8-Ø25 range, it conforms to the ISO 6432 mounting interface, dropping directly into standard mini-cylinder brackets and clevises. This specific SKU lacks the -S magnet, so it cannot accept CMSG, DMSG, or EMSG sensors. Based on the 0.5 MPa push force, it handles a safe working load of about 147 N, lifting roughly 12.5 kg vertically with a 2:1 safety margin.
Airtac MIC Cushioned Mini Cylinder MIC25X15CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X15CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 15 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X15CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×15 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X15CA Is Used
High-Speed Diverter
Snaps packages across a belt at high speed. The adjustable cushion absorbs the 15 mm stroke impact, protecting the 12.5 kg load from sudden jolts.
Light Press Assembly
Drives a small bearing into a housing using 245 N of push force. The needle-set cushion ensures the press stops smoothly without hammering the fixture.
Flap Folding Arm
Folds carton flaps rapidly in a washdown zone. The stainless construction resists moisture while the ISO 6432 clevis mount allows easy bracket alignment.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X15CA the Right Cylinder?
When sizing this 25 mm bore, stepping down to a MIC20 drops the 0.5 MPa push force to 157 N, while stepping up to a MIC32 raises it to 402 N. The adjustable cushion matters most when moving heavier loads at high speeds across the 30-800 mm/s range, protecting both the machinery and the workpiece from impact. The CA rear pivot cover provides a clevis mount for angular alignment.
Remember that the air cushion only decelerates the piston near the stroke end; it does not act as a lock or brake. If your application must hold a load vertically during air loss, add an external rod lock or a pilot-operated check valve. To add position sensing, you must switch to the -S magnet variant of this cylinder.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X15CA FAQ
This 25 mm bore cylinder features a 1/8" port and a 10 mm rod. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, increasing to 343.4 N push and 288.5 N pull at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa.
No, this specific SKU does not include a magnet, so it cannot accept CMSG, DMSG, or EMSG switches. You would need the -S variant for sensing. The adjustable air cushion at both ends functions only to decelerate the load, not to hold it in place.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X15CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.