Airtac MIC Cushioned Mini Cylinder MIC25X200CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X200CA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 200mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke200 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X200CA
Delivering 245.3 N of push force at 0.5 MPa, the AirTAC MIC25X200CA is a double-acting round-body mini cylinder built for demanding 200 mm stroke tasks. It features a stainless-steel barrel and piston rod to resist mild corrosion and washdown environments. Because this 25 mm bore uses the ISO 6432 mounting interface, it drops directly into standard mini-cylinder brackets and clevises.
The defining trait of the MIC series is the adjustable air cushion at both ends. By turning a needle valve, you tune the end-of-stroke deceleration to absorb high-speed shock, protecting your payload and lowering machine noise versus a fixed bumper. In practical terms, this actuator provides a safe working load of about 147 N and lifts roughly 12.5 kg vertically with a 2:1 safety margin. It uses a 1/8" port and an M10x1.25 male rod thread.
Airtac MIC Cushioned Mini Cylinder MIC25X200CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X200CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 200 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X200CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X200CA Is Used
Package Diverting
Handles 200 mm routing strokes on conveyor lines, using the tuned air cushion to softly stop heavier cartons without bounce.
Light Pressing
Applies up to 245.3 N of push force for seating small bearings or pins, with the stainless build surviving light coolant spray.
Pallet Gate Actuation
Drives 200 mm lift gates for pallet handling, where the CA clevis mount accommodates the slight arc of the moving load.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X200CA the Right Cylinder?
When sizing this 245.3 N (0.5 MPa push) actuator, consider the adjacent bores: stepping down to the MIC20 drops thrust to 157.0 N, while the larger MIC32 raises it to 402.2 N. The adjustable cushion matters most when driving heavier masses at high speeds up to 800 mm/s, letting you dial out end-of-stroke impact. This CA back cover equips the cylinder with a rear pivot clevis for articulated mounting.
Note that air loss causes the piston to drift; the cushion only decelerates near stroke end and acts purely as a shock absorber, never a brake. For suspended loads that must hold position, add an external rod lock or pilot check valve. Also, because this specific SKU lacks the -S suffix, it cannot accept CMSG, DMSG, or EMSG magnetic sensors.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X200CA FAQ
This 25 mm bore cylinder uses a 1/8" port and a Ø10 mm rod. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, or 343.4 N push and 288.5 N pull at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa.
No, this specific SKU lacks the internal magnet, so it cannot accept CMSG, DMSG, or EMSG switches. You would need the -S variant for position sensing. The adjustable air cushions and stainless steel construction are still present.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X200CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.