Airtac MIC Cushioned Mini Cylinder MIC25X250SCM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X250SCM is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 250mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke250 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X250SCM
Delivering 245.3 N of push force at 0.5 MPa, this double-acting stainless steel mini cylinder is built for demanding 250 mm stroke tasks. The Ø25 mm round-body design uses the ISO 6432 mounting interface, dropping smoothly into standard mini-cylinder brackets and clevises. A needle-set variable air cushion at both ends absorbs high-speed end-of-stroke shock, protecting your payload while reducing noise. The CM round rear cover provides a clean, standard port and mounting orientation.
The stainless-steel barrel and piston rod resist mild corrosion and washdown environments. With a 1/8" port and an M10x1.25 male rod thread, it lifts about 12.5 kg vertically with a 2:1 safety margin. Because this SKU includes the -S magnet, you can mount CMSG, DMSG, or EMSG sensors directly for position detection.
Airtac MIC Cushioned Mini Cylinder MIC25X250SCM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X250SCM |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 250 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X250SCM
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×250 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X250SCM Is Used
High-Speed Package Diverting
Uses the 245.3 N push force to deflect cartons on a fast line, relying on the adjustable air cushion to stop the 250 mm stroke smoothly without slamming.
Vertical Lift Gates
Lifts lightweight access gates weighing up to 12.5 kg, where the stainless build resists humidity and the cushion prevents shock on descent.
Light Assembly Pressing
Presses small bearings or pins with a 343.4 N push at 0.7 MPa, using the needle cushion to decelerate the tooling before contact.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X250SCM the Right Cylinder?
If you need less force, the Ø20 MIC bore provides 157 N of push at 0.5 MPa; stepping up to the Ø32 bore yields 402 N. Choose this Ø25 model when moving loads at high speeds where the adjustable air cushion is essential to prevent end-of-stroke impact. Remember that the cushion only decelerates the piston near the stroke end—it does not act as a brake. If your application must hold a load vertically during air loss, add an external rod lock or a pilot-operated check valve.
Mounting flexibility is excellent with LB foot, FA flange, SDB pivot, and TC trunnion options. The integrated -S magnet supports reed and electronic switches. For alternative actions, consider the MI bumper version, MID double-rod, or MIJ adjustable-stroke variants.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X250SCM FAQ
This double-acting cylinder has a 25 mm bore, a 10 mm piston rod, a 1/8" port, and an M10x1.25 male rod thread. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, 343.4 N push and 288.5 N pull at 0.7 MPa, with a theoretical maximum force of 50 kgf at 1.0 MPa.
The adjustable air cushion only decelerates the piston near the stroke end; it is not a lock or brake, so the piston will drift if air is lost. For holding, use an external rod lock. The -S magnet allows CMSG, DMSG, and EMSG sensors to track position.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X250SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.