Airtac MIC Cushioned Mini Cylinder MIC25X320CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X320CA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 320mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke320 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X320CA
Delivering 245.3 N of push force at 0.5 MPa, this double-acting stainless-steel round-body mini cylinder is built for demanding actuation. The Ø25 bore uses a 1/8" port and an M10x1.25 male rod thread. A defining feature is the adjustable air cushion at both ends, letting you dial in needle valves to absorb end-of-stroke shock at high cycling speeds, which protects the load and reduces noise better than a fixed bumper. The stainless barrel and rod resist mild corrosion and washdown environments.
This 320 mm stroke model drops directly into standard mini-cylinder brackets and clevises using the ISO 6432 mounting interface. It yields a safe working load of roughly 147 N, lifting about 12.5 kg vertically with a 2:1 safety margin. Note that this specific SKU lacks a magnet, so it cannot host CMSG, DMSG, or EMSG sensors without switching to the -S variant. The rear CA clevis cover simplifies pivot mounting for angular motion requirements.
Airtac MIC Cushioned Mini Cylinder MIC25X320CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X320CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 320 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X320CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×320 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X320CA Is Used
Diverter Gate Actuation
Snaps sorting gates at high speed on packaging lines; the adjustable air cushion prevents the 320 mm stroke from slamming, protecting the gate mechanism.
Light Press Assembly
Provides a steady 245.3 N push for seating small bearings, using the CA clevis to accommodate slight angular misalignment during the press cycle.
Pallet Stopper Arm
Halts empty pallets on a gravity conveyor; the stainless build shrugs off dusty ambient conditions while the cushion softens the stop impact.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X320CA the Right Cylinder?
When sizing this 245.3 N (0.5 MPa push) unit, stepping down to the Ø20 MIC bore drops force to 157.0 N, while stepping up to the Ø32 bore raises it to 402.2 N. Choose this Ø25 model for moderate loads moving at high velocities where the adjustable air cushion is essential to prevent harsh end-of-stroke impacts. For slower cycles, the simpler MI bumper version may suffice. Keep in mind the cushion only decelerates near the stroke end; it does not lock the rod. If you need to hold a load vertically during air loss, install an external rod lock or pilot check valve. Mounting options include LB foot, FA flange, SDB pivot, and TC trunnion, but this CA rear cover variant is optimized for clevis attachment.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X320CA FAQ
This double-acting cylinder has a 25 mm bore, a 1/8" port, and an M10x1.25 male rod thread. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, or 343.4 N push and 288.5 N pull at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa.
No, this specific SKU does not include a piston magnet, so it cannot support CMSG, DMSG, or EMSG switches. You must select the -S magnet variant for sensing. The adjustable air cushion at both ends only decelerates the load near stroke end and does not function as a brake or lock.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X320CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.