Airtac MIC Cushioned Mini Cylinder MIC25X450SCM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X450SCM is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 450mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke450 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X450SCM
Dial in end-of-stroke deceleration with the AirTAC MIC25X450SCM, a double-acting round-body mini cylinder built for high-speed actuation. A needle-set variable air cushion at both ends absorbs shock, protecting your payload while reducing noise. The stainless-steel barrel and piston rod supply mild corrosion resistance for washdown or humid settings.
Delivering 245.3 N of push force and 206.1 N of pull force at 0.5 MPa, this Ø25 bore unit handles substantial work for its footprint. It lifts about 12.5 kg vertically with a 2:1 safety margin. The 1/8" port and M10x1.25 male rod thread match standard mini-cylinder hardware, while the -S magnet enables CMSG, DMSG, and EMSG position sensing. The CM round end cover provides a clean rear mounting interface.
Airtac MIC Cushioned Mini Cylinder MIC25X450SCM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X450SCM |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 450 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X450SCM
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×450 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X450SCM Is Used
Package Diversion
Handles high-speed lane changing for heavier cartons, using the adjustable cushion to stop the 450 mm stroke smoothly without jarring the conveyor frame.
Clamshell Sealing
Provides the 245 N push force needed to hold and seal rigid plastic containers, while the stainless build resists daily washdown moisture.
Vertical Lift Gate
Raises and lowers a lightweight access panel, lifting roughly 12.5 kg safely and using the -S magnet to confirm gate position via DMSG sensors.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X450SCM the Right Cylinder?
When sizing this 25 mm bore, stepping down to the MIC20X50 drops the 0.5 MPa push force to 157 N, whereas moving up to the MIC32X75 raises it to 402 N. Choose this 450 mm stroke model for fast cycles where the adjustable air cushion prevents harsh impacts at the extremes of travel.
Note that the cushion only decelerates the load near the stroke end; it does not function as a brake. If you need to prevent drift on air loss or a centered valve, install an external rod lock or pilot-operated check valve. Mounting options include LB foot, FA flange, SDB pivot, and TC trunnion brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X450SCM FAQ
At 0.5 MPa this cylinder pushes with 245.3 N and pulls with 206.1 N. At 0.7 MPa the push is 343.4 N and pull is 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa. It uses a 1/8" air port and a Ø10 mm piston rod with an M10x1.25 male thread.
No, the needle-set air cushion only decelerates the piston near the end of its stroke to reduce shock; it is not a brake or locking mechanism. The piston will drift if air is lost or the valve is centered. You must add an external rod lock or pilot check valve to hold a suspended load.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X450SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.