Airtac MIC Cushioned Mini Cylinder MIC25X60CA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X60CA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 60mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X60CA
Tame high-speed end-of-stroke shock with the AirTAC MIC25X60CA, a double-acting round-body mini cylinder built with a stainless-steel barrel and rod for mild washdown resistance. It uses a needle-set adjustable air cushion at both ends to decelerate the load smoothly, reducing noise and impact compared to a fixed bumper. This Ø25 bore pushes 245.3 N and pulls 206.1 N at 0.5 MPa, yielding a safe working load of about 147 N or a 12.5 kg vertical lift with a 2:1 margin.
The 60 mm stroke unit features a CA rear clevis cover and a 1/8" port. It conforms to the ISO 6432 mounting interface for standard mini-cylinder brackets. Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG or EMSG sensors; order the -S variant if you require position sensing.
Airtac MIC Cushioned Mini Cylinder MIC25X60CA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X60CA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 60 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X60CA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X60CA Is Used
High-Speed Diverting
Uses the 245.3 N push force to knock parcels off a belt at 800 mm/s while the adjustable cushion absorbs the rod-end impact.
Carton Flap Folding
Drives a flap tucker at high cycle rates; the needle-set cushion prevents jarring stops that would tear cardboard.
Light Press Assembly
Provides a 12.5 kg vertical press load with a 2:1 margin for seating small bearings smoothly via the CA clevis mount.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X60CA the Right Cylinder?
If you need less force, the smaller Ø20 bore provides 157 N push at 0.5 MPa, while stepping up to the Ø32 bore yields 402 N. Choose this Ø25 model when moving heavier loads at high speed where the adjustable cushion is essential to prevent impact damage. Remember that the cushion only decelerates near the stroke end; it is not a brake. The piston will drift on air loss, so fit an external rod lock or pilot check valve if you must hold a load vertically.
The CA pivot cover suits articulated rod-end mounting. Match your hardware accordingly, and note again that this specific non-magnet SKU cannot host a reed switch.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X60CA FAQ
At 0.5 MPa it pushes 245.3 N and pulls 206.1 N. At 0.7 MPa it pushes 343.4 N and pulls 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa. The air port is 1/8".
No, this specific SKU lacks the internal magnet, so it cannot accept CMSG, DMSG or EMSG switches. You would need the -S variant for sensing. The stainless build resists mild corrosion, and the cushion only decelerates the load, acting as a brake.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X60CA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.