Airtac MIC Cushioned Mini Cylinder MIC25X60SCA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X60SCA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 60mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke60 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X60SCA
Delivering 245.3 N of push force at 0.5 MPa, the AirTAC MIC25X60SCA is a double-acting round-body mini cylinder built for demanding cycles. The stainless-steel rolled barrel and piston rod resist mild corrosion and washdown environments. Because this Ø25 bore uses the ISO 6432 mounting interface, it drops directly into standard mini-cylinder brackets and clevises without custom hardware.
A defining trait of the MIC series is the adjustable air cushion at both ends. By turning the cushion needle, you tune the end-of-stroke deceleration to absorb high-speed shock, protecting the load and cutting noise far better than a fixed rubber bumper. For sizing, this bore yields a safe working load of roughly 147 N and lifts about 12.5 kg vertically with a 2:1 margin. The unit includes a piston magnet for position sensing and uses a 1/8" port.
Airtac MIC Cushioned Mini Cylinder MIC25X60SCA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X60SCA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 60 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X60SCA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×60 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X60SCA Is Used
Package Diverting
Uses the 245.3 N push force to push cartons off a high-speed belt, relying on the adjustable cushion to prevent end-of-stroke slamming.
Clamshell Sealing
Closes light packaging presses where the 12.5 kg vertical lift capacity handles the upper platen smoothly.
Small Press Ejection
Ejects machined parts from a fixture, using the ISO 6432 mounting interface to fit standard clevis brackets easily.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X60SCA the Right Cylinder?
When sizing this actuator, look both ways: stepping down to the MIC20 drops the 0.5 MPa push force to 157.0 N, while moving up to the MIC32 raises it to 402.2 N. Choose this Ø25 model when your cycle speed approaches the 30-800 mm/s range and the adjustable needle cushion is required to smooth out heavy impacts. The rear CA clevis cover provides a pivot mount for angular movement.
Position detection requires the built-in magnet, which supports CMSG, DMSG, and EMSG switches; a SKU without the S designation cannot accept a sensor. Remember that the air cushion only decelerates the piston near the stroke end—it is not a brake. If the application must hold a load vertically during air loss, add an external rod lock or pilot check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X60SCA FAQ
This double-acting cylinder pushes 245.3 N and pulls 206.1 N at 0.5 MPa. At 0.7 MPa, it pushes 343.4 N and pulls 288.5 N. The theoretical maximum force is 50 kgf at 1.0 MPa, and the air port size is 1/8".
No. The adjustable air cushion only decelerates the piston near the end of the stroke; it is not a lock or brake. The piston will drift on air loss. For vertical load holding, install an external rod lock or pilot check valve. The -S magnet enables CMSG, DMSG, and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X60SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.