Airtac MIC Cushioned Mini Cylinder MIC25X75CM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X75CM is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 75mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X75CM
Dial in end-of-stroke deceleration with the AirTAC MIC25X75CM, a double-acting round-body mini cylinder built from stainless steel for mild washdown resistance. The CM rear cover provides a specific port and mounting orientation for tight assemblies. Featuring a 25 mm bore and 75 mm stroke, it delivers 245.3 N of push force and 206.1 N of pull force at 0.5 MPa.
A variable air cushion at both ends lets you turn a needle valve to absorb high-speed shock, protecting your payload far better than a fixed bumper. This yields a safe working load of roughly 147 N, lifting about 12.5 kg vertically with a 2:1 margin. It uses a 1/8" port and an M10x1.25 male rod thread. Because this SKU lacks the -S magnet, it cannot accept CMSG, DMSG, or EMSG position switches.
Airtac MIC Cushioned Mini Cylinder MIC25X75CM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X75CM |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 75 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X75CM
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X75CM Is Used
Package Diverting
Pushes cartons off a high-speed belt using 245.3 N of thrust, relying on the adjustable air cushion to stop the rod smoothly without slamming.
Clamping Lids
Holds lightweight container lids shut on a packaging line, where the stainless steel barrel shrugs off occasional washdown spray.
Small Press Ejection
Kicks formed parts out of a die at speed; the needle-set cushion absorbs the shock of the sudden ejection stroke end.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X75CM the Right Cylinder?
When sizing this 25 mm bore, dropping down to the MIC20 reduces your 0.5 MPa push force to 157 N, while stepping up to the MIC32 raises it to 402 N. Choose this model when moving heavier masses at high speeds where the adjustable end cushions actively prevent impact damage. The cushion only decelerates the piston near stroke end; it does not lock the rod. If your application must hold a load during air loss, install an external rod lock or pilot check valve.
The Ø25 body conforms to the ISO 6432 mini-cylinder mounting interface, dropping directly into standard brackets and clevises. You can mount it using LB foot, FA flange, SDB pivot, or TC trunnion hardware. For position sensing, you must select the -S magnet variant to use CMSG, DMSG, or EMSG switches, as this base SKU is unsensored.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X75CM FAQ
This 25 mm bore cylinder uses a 1/8" port and an M10x1.25 male rod thread. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, or 343.4 N push and 288.5 N pull at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa.
No, this specific SKU does not include a magnet, so it cannot accept CMSG, DMSG, or EMSG switches. You must purchase the -S variant for position sensing. The adjustable air cushions at both ends function normally to decelerate the load, but they do not lock or hold the rod in place.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X75CM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.