Airtac MIC Cushioned Mini Cylinder MIC25X80SCA
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC25X80SCA is a genuine double acting + cushion round-body mini air cylinder with a Ø25mm bore and 80mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments. Its ISO 6432 mounting interface makes it a compact drop-in for standard mini-cylinder fixtures.
- BoreØ25 mm
- Stroke80 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC25X80SCA
Dialing in end-of-stroke deceleration is effortless with the AirTAC MIC25X80SCA, a double-acting round-body mini cylinder built with a stainless-steel barrel and rod for mild washdown resistance. A needle-set variable air cushion at both ends absorbs high-speed shock, protecting your payload far better than a fixed bumper. Because the bore is Ø25, it conforms to the ISO 6432 mounting interface, dropping cleanly into standard mini-cylinder brackets and clevises.
This 80 mm stroke unit pushes with 245.3 N and pulls with 206.1 N at 0.5 MPa, peaking at a theoretical 50 kgf at 1.0 MPa. For practical sizing, that translates to a safe working load of roughly 147 N, or lifting about 12.5 kg vertically with a 2:1 safety margin. The 1/8" port and M10x1.25 male rod thread handle the airflow and linkage for this force class, while the CA rear pivot cover simplifies direct clevis mounting.
Airtac MIC Cushioned Mini Cylinder MIC25X80SCA Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC25X80SCA |
|---|---|
| Series | MIC ISO 6432 mini cylinder |
| Bore size | Ø25 mm |
| Stroke | 80 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G.
Theoretical Output Force (Ø25mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 245 N | 206 N |
| 0.7 MPa | 344 N | 289 N |
| Max (@1.0 MPa) | 50 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC25X80SCA
| MIC | ISO 6432 round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 25 | Bore size in mm. |
| ×80 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC25X80SCA Is Used
Package Diverting
Uses the 245.3 N push force at 0.5 MPa to snap diverters into place on a high-speed line, relying on the adjustable cushion to stop the 80 mm stroke smoothly without slamming.
Carton Sealing
Drives sealing heads with a safe working load near 147 N, where the stainless build resists occasional washdown and the CA clevis allows compact pivot mounting.
Light Pressing
Applies up to 50 kgf theoretical force for seating small bearings, using the needle-set end cushions to protect fragile components from end-of-stroke shock.
Is the Airtac MIC Cushioned Mini Cylinder MIC25X80SCA the Right Cylinder?
If your payload is lighter, stepping down to the MIC20X50 drops the 0.5 MPa push force to 157 N, saving space; if you need more muscle, the MIC32X75S jumps to 402 N. Keep this 25 mm bore when running at high speeds where the adjustable air cushion is critical to prevent impact damage. The cushion only decelerates the piston near the stroke end, so remember it is not a brake. If the load must hold position during air loss, install an external rod lock or pilot check valve. This SKU includes the -S magnet for CMSG, DMSG, or EMSG sensors, and pairs with LB, FA, SDB, or TC mounts.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC25X80SCA FAQ
This double-acting cylinder has a 1/8" port and an M10x1.25 male rod thread. It generates 245.3 N push and 206.1 N pull at 0.5 MPa, or 343.4 N push and 288.5 N pull at 0.7 MPa. The theoretical maximum force is 50 kgf at 1.0 MPa.
No, the adjustable air cushion only decelerates the piston near the end of the stroke and acts purely as a shock absorber, never as a brake or lock. The piston will drift on air loss, so you must use an external rod lock or pilot-operated check valve for vertical load holding. The built-in -S magnet supports CMSG, DMSG, and EMSG sensors.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC25X80SCA
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.