Airtac MIC Cushioned Mini Cylinder MIC32X10SCM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC32X10SCM is a genuine double acting + cushion round-body mini air cylinder with a Ø32mm bore and 10mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke10 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC32X10SCM
Delivering 402.2 N of push force at 0.5 MPa, this double-acting round-body mini cylinder handles heavier workloads with precision. The MIC32X10SCM features a 32 mm bore, a 10 mm stroke, and a 1/8 inch air port. Its stainless-steel barrel and rod resist mild corrosion, making the unit suitable for washdown environments. A built-in piston magnet allows for CMSG, DMSG, or EMSG sensor integration.
Unlike standard bumper models, this actuator uses a variable air cushion at both ends. You can tune the needle valve to decelerate loads smoothly at high speeds, reducing shock and noise. With a safe working load of roughly 241 N, it lifts about 20.5 kg vertically using a 2:1 safety margin. The CM round end cover provides a clean rear mounting interface for your assembly.
Airtac MIC Cushioned Mini Cylinder MIC32X10SCM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC32X10SCM |
|---|---|
| Series | MIC mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 10 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC32X10SCM
| MIC | round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×10 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC32X10SCM Is Used
High-Speed Diverting
Pushes packages rapidly across sorting lanes. The adjustable air cushion absorbs the end-of-stroke impact, protecting the 402 N drive mechanism from high-cycle shock.
Carton Sealing Press
Applies steady clamping force on assembly lines. The stainless construction handles splashes, while the 10 mm short stroke delivers rapid, repeatable actuation.
Component Insertion
Drives bearings into housings with precise force. The needle-set cushion decelerates the rod just before contact, preventing damage to sensitive parts at 800 mm/s.
Is the Airtac MIC Cushioned Mini Cylinder MIC32X10SCM the Right Cylinder?
When sizing this 32 mm bore actuator, stepping down to a MIC25 model reduces the push force to 245.3 N at 0.5 MPa, while stepping up to a MIC40 increases it to 628.3 N. Choose this 32 mm option when your application requires substantial force combined with high-speed cycling that would overwhelm a fixed bumper. The adjustable cushion needle lets you dial in the exact deceleration needed to protect the load.
Because this is a double-acting cylinder, it does not hold position on air loss; the piston drifts if pressure drops, as the cushion only decelerates near the stroke end and acts as no brake. For suspended loads, install an external rod lock or pilot check valve. The -S suffix confirms the magnet is present for switches, and you can mount the body using LB foot, FA flange, SDB pivot, or TC trunnion brackets.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC32X10SCM FAQ
This 32 mm bore cylinder features a 1/8 inch air port and a 12 mm rod. It generates 402.2 N push and 345.6 N pull at 0.5 MPa, or 563 N push and 483.8 N pull at 0.7 MPa. The theoretical maximum force is 82 kgf at 1.0 MPa.
No, the variable air cushion only decelerates the piston near the stroke end to reduce shock; it is not a brake or lock. The -S suffix indicates a built-in magnet for CMSG, DMSG, or EMSG switches. You must use an external rod lock to hold a load on air loss.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC32X10SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.