Airtac MIC Cushioned Mini Cylinder MIC32X140SCM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC32X140SCM is a genuine double acting + cushion round-body mini air cylinder with a Ø32mm bore and 140mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke140 mm
- Port size1/4"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC32X140SCM
Delivering 402.2 N of push force at 0.5 MPa, the AirTAC MIC32X140SCM is a double-acting round-body mini cylinder built for demanding cycles. The stainless-steel barrel and rod shrug off mild corrosion, making it suitable for washdown environments. A needle-set variable air cushion at both ends absorbs high-speed end-of-stroke shock, protecting your payload and reducing noise far better than a fixed rubber bumper.
This 32 mm bore unit pushes 563 N at 0.7 MPa and pulls 345.6 N at 0.5 MPa through a 1/4 inch port. It yields a safe working load of roughly 241 N, lifting about 20.5 kg vertically with a 2:1 margin. The CM round rear cover provides a clean back-end profile. Because the unit includes the S magnet, you can mount CMSG, DMSG or EMSG switches for position sensing.
Airtac MIC Cushioned Mini Cylinder MIC32X140SCM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC32X140SCM |
|---|---|
| Series | MIC mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 140 mm |
| Acting type | Double acting + cushion |
| Port size | 1/4" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC32X140SCM
| MIC | round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×140 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC32X140SCM Is Used
High-Speed Carton Diverting
Uses the 402.2 N push force to deflect heavy packages on a sorter, relying on the adjustable air cushion to halt the 140 mm stroke quietly without slamming.
Vertical Flap Folding
Lifts about 20.5 kg of folding mechanism vertically, using the stainless build to resist moisture from adhesive lines while the needle cushion softens the upstroke.
Component Pressing
Applies 563 N at 0.7 MPa to seat bearings, where the 1/4 inch port ensures adequate flow and the CM cover keeps the rear compact against the machine frame.
Is the Airtac MIC Cushioned Mini Cylinder MIC32X140SCM the Right Cylinder?
If 402.2 N is excessive, drop to the MIC25 which provides 245.3 N at 0.5 MPa. If you need more power, the MIC40 pushes 628.3 N. The adjustable cushion matters most when driving heavy loads at high speed across the 140 mm stroke, as it decelerates the piston smoothly. Remember the cushion only slows the load near stroke end; it is not a brake. The piston will drift on air loss, so fit an external rod lock or pilot check valve if you must hold position. You can mount this cylinder using LB foot, FA flange, SDB pivot or TC trunnion hardware.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC32X140SCM FAQ
This double-acting cylinder uses a 1/4 inch port and a 12 mm rod. It generates 402.2 N push and 345.6 N pull at 0.5 MPa, or 563 N push and 483.8 N pull at 0.7 MPa. The theoretical maximum force is 82 kgf at 1.0 MPa.
The S suffix means it has a built-in magnet for CMSG, DMSG or EMSG sensors. It cannot hold a load on air loss; the piston drifts and the adjustable air cushion only decelerates near stroke end, so you need a pilot check valve for vertical holding.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC32X140SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.