Airtac MIC Cushioned Mini Cylinder MIC32X75SCM
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC32X75SCM is a genuine double acting + cushion round-body mini air cylinder with a Ø32mm bore and 75mm stroke, 1/8" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ32 mm
- Stroke75 mm
- Port size1/8"
- Acting typeDouble acting + cushion
- Rod threadM10×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC32X75SCM
Delivering 402.2 N of push force at 0.5 MPa, this stainless-steel round-body mini cylinder brings adjustable air cushioning to heavier automation tasks. The needle-set cushion at both ends absorbs high-speed end-of-stroke impact, protecting payloads while reducing noise compared to fixed bumper designs. Its riveted stainless barrel and Ø12 mm rod shrug off mild corrosion and washdown environments.
Equipped with a 1/8" port and an M10x1.25 male rod thread, the double-acting MIC32X75SCM is built for a 75 mm travel range. The integrated -S magnet enables CMSG, DMSG, or EMSG position sensing, while the CM round rear cover provides a clean mounting footprint. For vertical lifts, expect a safe working capacity of roughly 24.1 kg with a 2:1 safety margin.
Airtac MIC Cushioned Mini Cylinder MIC32X75SCM Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC32X75SCM |
|---|---|
| Series | MIC mini cylinder |
| Bore size | Ø32 mm |
| Stroke | 75 mm |
| Acting type | Double acting + cushion |
| Port size | 1/8" |
| Rod thread | M10×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø32 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø32mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 402 N | 346 N |
| 0.7 MPa | 563 N | 484 N |
| Max (@1.0 MPa) | 82 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC32X75SCM
| MIC | round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 32 | Bore size in mm. |
| ×75 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC32X75SCM Is Used
Carton Diverting
Uses the 402.2 N push force to deflect heavy packaged goods on a high-speed sorting line, relying on the air cushion to silently stop the 75 mm stroke.
Component Pressing
Applies steady downward pressure to seat bearings or pins, where the 1/8" port delivers ample flow for rapid cycling and the cushion prevents impact damage.
Vertical Lift Gates
Raises lightweight access doors up to 20.5 kg, utilizing the built-in -S magnet for DMSG sensors to confirm gate position at both ends of travel.
Is the Airtac MIC Cushioned Mini Cylinder MIC32X75SCM the Right Cylinder?
When sizing this 32 mm bore, step down to the MIC25 (245.3 N push @0.5 MPa) for lighter loads, or move up to the MIC40 (628.3 N push @0.5 MPa) when you need more thrust. Choose this model when cycle speeds demand the adjustable air cushion to prevent harsh end-stroke slamming. Note that while the cushion decelerates the piston, it does not lock the load; if air pressure drops, the rod will drift, requiring an external rod lock or pilot check valve for secure holding.
The -S magnet allows seamless mounting of CMSG, DMSG, and EMSG sensors. You can pair the CM back cover with LB foot, FA flange, SDB pivot, or TC trunnion hardware to fit your frame. If you need a double rod, consider the MID, or the MIJ for adjustable stroke variants.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC32X75SCM FAQ
This double-acting cylinder uses a 1/8" port and generates 402.2 N push / 345.6 N pull at 0.5 MPa, and 563 N push / 483.8 N pull at 0.7 MPa. Its theoretical maximum force is 82 kgf at 1.0 MPa.
No. The adjustable air cushion only decelerates the piston near stroke end and acts purely as a shock absorber, never as a brake. For vertical load holding during air loss, you must install an external rod lock or pilot-operated check valve.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC32X75SCM
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.