Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC
The AirTAC Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC is a genuine double acting + cushion round-body mini air cylinder with a Ø40mm bore and 200mm stroke, 1/4" air ports and a stainless-steel barrel and rod for mildly corrosive environments.
- BoreØ40 mm
- Stroke200 mm
- Port size1/4"
- Acting typeDouble acting + cushion
- Rod threadM12×1.25
- CushionVariable air cushion, both ends
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC
Delivering 628.3 N of push force at 0.5 MPa, the MIC40X200SUTC is a robust double-acting round-body mini cylinder built for demanding motion tasks. Its stainless-steel barrel and Ø16 mm piston rod resist mild corrosion and washdown environments. A 1/4" port feeds the chamber, while the U back cover provides a 90-degree mounting orientation. Equipped with an -S piston magnet, it supports CMSG, DMSG, and EMSG sensors for precise end-of-stroke detection.
Twin adjustable air cushions at both ends allow you to needle-set the deceleration, soaking up high-speed kinetic energy to protect your payload and cut noise. This makes it highly effective for moving heavier loads, offering a safe working load of about 377 N or lifting roughly 32 kg vertically with a 2:1 safety margin. The cushion only decelerates near the stroke end; it does not lock the rod.
Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC Technical Specifications
| Model | Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC |
|---|---|
| Series | MIC mini cylinder |
| Bore size | Ø40 mm |
| Stroke | 200 mm |
| Acting type | Double acting + cushion |
| Port size | 1/4" |
| Rod thread | M12×1.25 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 800 mm/s |
| Cushion | Variable air cushion, both ends |
| Max standard stroke | Up to 500 mm |
Specifications follow the official AirTAC MI/MIC (ISO 6432) datasheet. Barrel & rod: stainless steel (round-body, riveted construction). Thread options: PT (blank) / G. Note: the Ø40 bore is a larger, non-ISO-6432 size.
Theoretical Output Force (Ø40mm)
| Pressure | Push force | Pull force |
|---|---|---|
| 0.5 MPa | 628 N | 528 N |
| 0.7 MPa | 880 N | 739 N |
| Max (@1.0 MPa) | 128 kgf | |
Actual usable force is lower than theoretical due to friction and back-pressure. Size with a safety margin.
Model Code: Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC
| MIC | round-body mini cylinder (double-acting, variable cushion). |
|---|---|
| 40 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -S | Optional built-in magnet for CMSG / DMSG / EMSG sensors. |
MI-family variants: MI / MIC (double acting ±cushion), MSI / MTI (single acting push / pull), MID / MICD (double rod ±cushion), MIJ / MICJ (adjustable stroke ±cushion). Back covers CA / U / R / CM. Mounting LB / FA / SDB / TC.
Where the Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC Is Used
Heavy Package Diversion
Pushes heavy cartons across high-speed sorting lines where the adjustable cushion prevents harsh slams that could damage packaging.
Vertical Load Lowering
Lowers approximately 32 kg payloads smoothly, using the needle-set cushion to absorb gravitational kinetic energy at the stroke end.
Pallet Pressing
Applies consistent 628.3 N clamping force at 0.5 MPa for light assembly or palletizing tasks, with the -S magnet confirming cycle completion.
Is the Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC the Right Cylinder?
When sizing this 40 mm bore, stepping down to a MIC32 yields 402.2 N push at 0.5 MPa, whereas no larger MIC bore exists. Choose this 40 mm model when moving substantial mass at high speeds where fixed bumpers would fail. The TC trunnion mount pairs with the U back cover for complex pivot geometries.
Remember that a standard cylinder drifts when air pressure drops, as the air cushion provides deceleration only, not a braking lock. For vertical or suspended loads that must hold position on air loss, integrate an external rod lock or pilot-operated check valve.
Quick checklist
- ✓ Required force at your working pressure
- ✓ Stroke and mounting space
- ✓ Port/thread type (PT / G)
- ✓ Magnet (-S) for sensors?
- ✓ Back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC)
Installation & Maintenance Notes
- check Use clean air filtered to 40µm or finer.
- check Keep within 0.15 – 1.0 MPa operating pressure.
- check Avoid side load on the piston rod.
- check Do not dismantle the riveted front/back covers.
- check Use correct back cover (CA/U/R/CM) & mount (LB/FA/SDB/TC).
- check Installation by qualified personnel per AirTAC docs.
Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC FAQ
This 40 mm bore cylinder features a 1/4" port and an M12x1.25 male rod thread. It generates 628.3 N push and 527.8 N pull at 0.5 MPa, 879.6 N push and 738.9 N pull at 0.7 MPa, with a theoretical maximum force of 128.1 kgf at 1.0 MPa.
The -S suffix indicates a built-in piston magnet for CMSG, DMSG, or EMSG sensors. The adjustable air cushion only decelerates the piston near stroke end and does not act as a brake; the cylinder will drift on air loss, so use an external rod lock or pilot check valve to hold suspended loads.
Authorized Export Seller
Genuine AirTAC parts produced by AirTAC factory.
1-Year Warranty
Covers non-human-caused product damage.
Fast Dispatch
Standard models are processed and dispatched in 3-5 business days.
Fast Reply
Most inquiries answered within 7-8 hours.
Request a Quote for Airtac MIC Cushioned Mini Cylinder MIC40X200SUTC
Send us the quantity and destination. We confirm price, stock and lead time — usually within 7-8 hours.