verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 3V1 · 3/2-Way Solenoid Valve

Airtac 3V1 Solenoid Valve 3V106B7FT

The AirTAC 3V1 Solenoid Valve 3V106B7FT is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.

  • Valve type3/2-way (3-port, 2-position)
  • Port size1/8 in
  • Coil voltageDC24V
  • Electrical entryDIN plug (DIN socket type)
  • Stations7
  • Series3V1
$170.15 $177.65Save 4% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every 3V1-06 voltage, entry and configuration on one page All 3V1-06 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac 3V1 Solenoid Valve 3V106B7FT

The 3V106B7FT mounts seven complete 3/2 valves on one shared base, so a 1/8in NPT port bank that would need seven separate bodies and seven sets of piping collapses into a single block. Each position is a direct-acting, single-solenoid unit with spring return: energise it and the outlet is fed, de-energise it and the spring vents the line. Like every 3V1, it is supplied in a single fixed initial state - confirm it on the datasheet before you design the panel logic.

The DC24V coils are the reason this body suits dense electronic panels: each draws just 3.0 W, and IP65 (DIN 40050) sealing protects the DIN plug entry in washdown-prone cabinets. Every valve also carries a manual override, so fixture set-up can be checked without power.

Airtac 3V1 Solenoid Valve 3V106B7FT Technical Specifications

ModelAirtac 3V1 Solenoid Valve 3V106B7FT
Series3V1
Valve type3/2-way (3-port, 2-position)
FunctionDirect-acting, single solenoid, spring return
Port size1/8 in
ThreadNPT
Coil voltageDC24V
Electrical entryDIN plug (DIN socket type)
Coil power3.0 W
Operating pressure0-0.8 MPa (0-114 psi)
Vacuum serviceNot rated for vacuum
Flow coefficientNot published for 3V1
Temperature-20 to 70 C
ConstructionDirect-acting, single solenoid, spring return
ProtectionIP65 (DIN 40050)
MediumAir, filtered by a 40 µm or finer element. Lubrication not required.

Figures follow the official AirTAC 3V1 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.

3V1 has no published flow coefficient. There is no Cv and no effective-area figure for this body in the source, so we do not print one. If the duty is flow-critical, ask us and we will confirm it, or step up to 3V2 (Cv 0.18-0.19) or 3V3 (Cv 0.62).

Model Code: Airtac 3V1 Solenoid Valve 3V106B7FT

3V1Body — sets the flow, the coil power and whether vacuum is rated.
1/8 inPort size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in.
DC24VCoil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V.
—Electrical entry: I = flying lead, otherwise a DIN plug.
7F7 stations in one assembly.
NPTPort thread. PT is standard; G and NPT are available to order.

What a 3/2 Valve Does

A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.

That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.

It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.

Where the Airtac 3V1 Solenoid Valve 3V106B7FT Is Used

view_module

Spot-welding fixture clamp bank

Seven single-acting clamp cylinders on an automotive spot-welding jig are each switched from one position of the 7F base, with spring return dropping every clamp when the cell powers down.

bolt

Screw-machine chip blow-off

A short air blast between cycles clears chips from a Swiss lathe cutting zone; the direct-acting valve fires the jet on command and vents the nozzle line when the cycle ends.

tune

Pilot stage on a transfer line

The 3.0 W DC24V coil makes the valve an economical pilot: a PLC output switches it, and its outlet signal indexes a larger main valve further down the transfer line.

Is the Airtac 3V1 Solenoid Valve 3V106B7FT the Right Part?

Flow is the open question on this body: AirTAC publishes no Cv or effective area for the 3V1, so for anything flow-critical send us the duty and we will confirm the size. If a single 1/8in valve proves too small, step up to the 3V2 (1/8in and 1/4in, NC or NO selectable, Cv 0.18-0.19, vacuum rated) or the 3V3 (1/4in, Cv 0.62); where manifold density matters more than flow, the 3V2M is the alternative base. A double-acting cylinder needs a 5-port valve - that is the AirTAC 4V series, not this one.

Before ordering, match five points: port (M5 or 1/8in), thread (NPT on this code), coil voltage (here DC24V at 3.0 W), electrical entry (this code uses the DIN plug, not the flying-lead I option) and station count (this assembly is 7F).

Confirm before you order

  • ✓ Port size and thread (PT standard; G / NPT to order)
  • ✓ Coil voltage matches your controller output
  • ✓ Electrical entry — DIN plug or flying lead
  • ✓ Single valve, bare base, or complete assembly
  • ✓ Single-acting duty, not double-acting
Ask an Engineer

Installation & Wiring Notes

  • check Use clean air filtered to 40µm or finer.
  • check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
  • check Match the coil voltage to your controller output.
  • check Use the manual override to test before powering up.
  • check Leave the exhaust port clear, or fit a silencer.
  • check Blank any unused station on the base before pressurising.
  • check Wiring by qualified personnel, per AirTAC documentation.

Airtac 3V1 Solenoid Valve 3V106B7FT FAQ

It is a 3/2 direct-acting, single-solenoid, spring-return valve with 1/8in NPT ports. Operating pressure is 0-0.8 MPa (0-114 psi), media temperature -20 to 70 C, protection IP65 (DIN 40050). Coil power at the listed voltages: AC220V 4.5 VA, AC110V 4.5 VA, AC24V 5.0 VA, DC24V 3.0 W, DC12V 2.5 W - this build uses DC24V. No flow coefficient (Cv) is published for the 3V1 series.

Seven valves share one base, one supply connection and one fixing job, which saves panel space and piping. Each position stays independently switchable, keeps its manual override, and runs on air filtered to 40 um or finer with no lubrication needed.

T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.

verified

Authorized Export Seller

Genuine AirTAC parts produced by the AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Request a Quote for Airtac 3V1 Solenoid Valve 3V106B7FT

Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for 3V106B7FT and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.