AirTAC TCM100 Guided Air Cylinder, 100 mm Bore
Every AirTAC TCM100 configuration on one page: 16 stock order codes with strokes from 25 to 250 mm, from $294.95. Pick a stroke, port thread and version to see the exact order code and price.
PT ports
Magnet (S)
This combination is not a stock order code. Request a quote and we will confirm availability and price.
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC TCM100
The AirTAC TCM100 is a double-acting three-rod guided cylinder (bronze-bushing guides) with a 100 mm bore. At 0.5 MPa it pushes 3927 N and pulls 3681.6 N; at 0.7 MPa, 5497.8 N push and 5154.2 N pull. Force depends on bore and pressure only, so every stroke on this page gives the same output.
Two guide rods run in bronze sleeve bearings (M), suited to side loads and impact; the body mounts from the top, rear or underside. All TCM100 versions use 3/8" air ports and run on filtered air at 0.15 to 1.0 MPa (proof 1.5 MPa), from -20 to +70 °C, at 50 to 400 mm/s. This page lists 16 stock order codes with strokes from 25 to 250 mm; the catalog maximum stroke is 250 mm.
TCM100 Technical Specifications
| Bore size | Ø100 mm |
|---|---|
| Piston rod | Ø25 mm |
| Stock strokes | 25 – 250 mm |
| Catalog maximum stroke | 250 mm |
| Port size | 3/8" (PT standard) |
| Fluid | Air (filtered by 40 µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 400 mm/s |
| Cushion | Rubber bumpers at both ends |
| Guide bearing | Bronze sleeve bearing (M) |
Source: AirTAC Products Catalog 2026A (PDF01-P0522/P0523), TC (TCL/TCM) series ordering code and specifications.
Theoretical output force (Ø100 mm)
| Pressure | Push | Pull |
|---|---|---|
| 0.5 MPa | 3927 N | 3681.6 N |
| 0.7 MPa | 5497.8 N | 5154.2 N |
Push = pressure × bore area; pull subtracts the Ø25 mm rod area. Usable force is lower because of friction and back-pressure.
How the TCM100 Order Code Is Built
| TCM100 | Series and bore (100 mm) |
|---|---|
| X50 | Stroke in mm |
| S | Built-in magnet for position sensors (every code) |
| G / T | Port thread: G = G (BSPP), T = NPT, blank = PT |
All AirTAC TCM100 Order Codes (16)
Each order code links to its own datasheet page. Use Select to load it into the configurator above.
| Order code | Stroke (mm) | Port thread | Magnet | Price | Select |
|---|---|---|---|---|---|
| TCM100X25S | 25 mm | PT ports | Magnet (S) | $294.95 | |
| TCM100X30S | 30 mm | PT ports | Magnet (S) | $300.99 | |
| TCM100X40S | 40 mm | PT ports | Magnet (S) | $314.75 | |
| TCM100X50S | 50 mm | PT ports | Magnet (S) | $328.70 | |
| TCM100X60S | 60 mm | PT ports | Magnet (S) | $342.41 | |
| TCM100X70S | 70 mm | PT ports | Magnet (S) | $356.37 | |
| TCM100X75S | 75 mm | PT ports | Magnet (S) | $364.28 | |
| TCM100X80S | 80 mm | PT ports | Magnet (S) | $370.12 | |
| TCM100X90S | 90 mm | PT ports | Magnet (S) | $384.08 | |
| TCM100X100S | 100 mm | PT ports | Magnet (S) | $397.77 | |
| TCM100X125S | 125 mm | PT ports | Magnet (S) | $433.39 | |
| TCM100X150S | 150 mm | PT ports | Magnet (S) | $468.96 | |
| TCM100X175S | 175 mm | PT ports | Magnet (S) | $504.58 | |
| TCM100X200S | 200 mm | PT ports | Magnet (S) | $540.15 | |
| TCM100X225S | 225 mm | PT ports | Magnet (S) | $575.77 | |
| TCM100X250S | 250 mm | PT ports | Magnet (S) | $611.33 |
Need a combination that is not listed? Request a quote.
Where the TCM100 Is Used
Pick-and-place and stoppers
Guide rods keep tooling square while the cylinder delivers about 3927 N at 0.5 MPa.
Pushers with side load
The guide rods take side load that would wear a plain cylinder rod.
Lifting and transfer units
Mounts from the top, back or underside to fit compact stations.
Choosing the Right TCM100 Configuration
Start with the stroke. Pick the exact travel your machine needs; a longer stroke adds length and air consumption without adding force. If your length is not listed, request a quote and we will confirm whether it can be built.
Finally pick the version: every code carries a magnet for position sensors.
AirTAC TCM100 FAQ
No. Every TCM100 gives about 3927 N push and 3681.6 N pull at 0.5 MPa, whatever the stroke.
3/8" ports, PT thread as standard.
0.15 to 1.0 MPa operating pressure (proof 1.5 MPa), 50 to 400 mm/s and -20 to +70 °C on filtered air.
Usually yes. Request a quote with the stroke and version and we will confirm whether it can be built, plus price and lead time.
No. You can order a single TCM100. Orders are processed and handed to the carrier within 3-5 business days.
Buying the TCM100 from AirtacDistr
Genuine AirTAC parts
Every order code on this page is the AirTAC factory part number. Specifications follow the AirTAC Products Catalog 2026A. About us
Ready in 3-5 business days
That is our time to process the order and hand it to the carrier. No minimum order: a single piece can be ordered.
14-day returns, 1-year warranty
Return within 14 days of delivery; the buyer pays return shipping. The warranty covers defects not caused by misuse. Return policy
Engineering help
Send your application details and we will confirm the right order code, usually within 7-8 hours. Ask us
Page data checked against the live catalog on 2026-10-30.
Request a Quote for the TCM100
Send the order code, quantity and destination. We confirm price, stock and lead time, usually within 7-8 hours.