AirTAC HLS12 Slide Table Cylinder, 12 mm Bore
Every AirTAC HLS12 configuration on one page: 49 stock order codes with strokes from 10 to 100 mm, from $184.21. Pick a stroke, external stopper and version to see the exact order code and price.
Magnet (S) · M5×0.8
This combination is not a stock order code. Request a quote and we will confirm availability and price.
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC HLS12
The AirTAC HLS12 is a double-acting twin-rod precision slide table (crossed-roller guide, standard type) with a 12 mm bore. At 0.5 MPa it pushes 113.1 N and pulls 84.8 N; at 0.7 MPa, 158.3 N push and 118.8 N pull. Force depends on bore and pressure only, so every stroke on this page gives the same output.
A crossed-roller guide gives high rigidity and precision without rotation; twin pistons double the output and a floating joint keeps load moments off the piston rods. All HLS12 versions use M5×0.8 air ports and run on filtered air at 0.15 to 0.7 MPa (proof 1.2 MPa), from -20 to +70 °C, at 50 to 500 mm/s. This page lists 49 stock order codes with strokes from 10 to 100 mm; the catalog maximum stroke is 100 mm.
HLS12 Technical Specifications
| Bore size | Ø12 mm |
|---|---|
| Piston rod | Ø6 mm × 2 |
| Stock strokes | 10 – 100 mm |
| Catalog maximum stroke | 100 mm |
| Port size | M5×0.8 |
| Fluid | Air (filtered by 40 µm element) |
|---|---|
| Operating pressure | 0.15 – 0.7 MPa |
| Proof pressure | 1.2 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 50 – 500 mm/s |
| Cushion | Fixed bumpers at both ends; shock absorbers on B, BS, BF versions |
| Guide | Crossed roller |
| Table type | Standard |
| Sensors | CMSH, DMSH, EMSH |
Source: AirTAC Products Catalog 2026A (PDF01-P0579/P0580), HLS/HLSL series ordering code and specifications.
Theoretical output force (Ø12 mm)
| Pressure | Push | Pull |
|---|---|---|
| 0.5 MPa | 113.1 N | 84.8 N |
| 0.7 MPa | 158.3 N | 118.8 N |
Twin pistons: push = 2 × pressure × bore area; pull subtracts both rod areas. Usable force is lower because of friction and back-pressure.
How the HLS12 Order Code Is Built
| HLS12 | Series and bore (12 mm) |
|---|---|
| X50 | Stroke in mm |
| S | Built-in magnet for position sensors (every code) |
| A / AS / AF / B / BS / BF | External stopper: adjusting bolts at both ends; adjusting bolt at the extend end; adjusting bolt at the retract end; shock absorbers at both ends; shock absorber at the extend end; shock absorber at the retract end (blank = none) |
All AirTAC HLS12 Order Codes (49)
Each order code links to its own datasheet page. Use Select to load it into the configurator above.
| Order code | Stroke (mm) | External stopper | Magnet · Thread | Price | Select |
|---|---|---|---|---|---|
| HLS12X10S | 10 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $184.21 | |
| HLS12X10SA | 10 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $209.80 | |
| HLS12X10SAS | 10 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $200.49 | |
| HLS12X10SAF | 10 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $194.71 | |
| HLS12X10SB | 10 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $256.33 | |
| HLS12X10SBS | 10 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $223.76 | |
| HLS12X10SBF | 10 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $217.97 | |
| HLS12X20S | 20 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $190.26 | |
| HLS12X20SA | 20 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $215.85 | |
| HLS12X20SAS | 20 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $206.54 | |
| HLS12X20SAF | 20 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $200.76 | |
| HLS12X20SB | 20 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $262.38 | |
| HLS12X20SBS | 20 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $229.81 | |
| HLS12X20SBF | 20 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $224.02 | |
| HLS12X30S | 30 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $196.10 | |
| HLS12X30SA | 30 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $221.69 | |
| HLS12X30SAS | 30 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $212.39 | |
| HLS12X30SAF | 30 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $206.54 | |
| HLS12X30SB | 30 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $268.22 | |
| HLS12X30SBS | 30 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $235.65 | |
| HLS12X30SBF | 30 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $229.81 | |
| HLS12X40S | 40 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $204.01 | |
| HLS12X40SA | 40 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $229.60 | |
| HLS12X40SAS | 40 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $220.30 | |
| HLS12X40SAF | 40 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $214.45 | |
| HLS12X40SB | 40 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $276.13 | |
| HLS12X40SBS | 40 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $243.56 | |
| HLS12X40SBF | 40 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $237.72 | |
| HLS12X50S | 50 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $211.92 | |
| HLS12X50SA | 50 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $237.51 | |
| HLS12X50SAS | 50 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $228.21 | |
| HLS12X50SAF | 50 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $222.36 | |
| HLS12X50SB | 50 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $284.04 | |
| HLS12X50SBS | 50 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $251.47 | |
| HLS12X50SBF | 50 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $245.63 | |
| HLS12X75S | 75 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $269.36 | |
| HLS12X75SA | 75 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $294.95 | |
| HLS12X75SAS | 75 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $285.64 | |
| HLS12X75SAF | 75 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $279.85 | |
| HLS12X75SB | 75 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $341.47 | |
| HLS12X75SBS | 75 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $308.90 | |
| HLS12X75SBF | 75 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $303.12 | |
| HLS12X100S | 100 mm | Basic (no external stopper) | Magnet (S) · M5×0.8 | $324.72 | |
| HLS12X100SA | 100 mm | A: adjusting bolts at both ends | Magnet (S) · M5×0.8 | $350.32 | |
| HLS12X100SAS | 100 mm | AS: adjusting bolt at the extend end | Magnet (S) · M5×0.8 | $341.01 | |
| HLS12X100SAF | 100 mm | AF: adjusting bolt at the retract end | Magnet (S) · M5×0.8 | $335.22 | |
| HLS12X100SB | 100 mm | B: shock absorbers at both ends | Magnet (S) · M5×0.8 | $396.84 | |
| HLS12X100SBS | 100 mm | BS: shock absorber at the extend end | Magnet (S) · M5×0.8 | $364.28 | |
| HLS12X100SBF | 100 mm | BF: shock absorber at the retract end | Magnet (S) · M5×0.8 | $358.48 |
Need a combination that is not listed? Request a quote.
Where the HLS12 Is Used
Precision pick-and-place
Twin pistons give about 113.1 N at 0.5 MPa with a rigid, guided table.
Positioning with stoppers
Adjusting bolts or shock absorbers set and cushion each end position.
Assembly and test stations
Fixtures mount directly on the slide table.
Choosing the Right HLS12 Configuration
Start with the stroke. Pick the exact travel your machine needs; a longer stroke adds length and air consumption without adding force. If your length is not listed, request a quote and we will confirm whether it can be built.
Then choose the external stopper. Adjusting bolts (A, AS, AF) set the end position precisely; shock absorbers (B, BS, BF) take the impact of heavier or faster loads. The letter after A or B picks the end: S = extend end, F = retract end, none = both ends.
Finally pick the version: every code carries a magnet for position sensors.
AirTAC HLS12 FAQ
No. Every HLS12 gives about 113.1 N push and 84.8 N pull at 0.5 MPa, whatever the stroke.
M5×0.8 ports.
0.15 to 0.7 MPa operating pressure (proof 1.2 MPa), 50 to 500 mm/s and -20 to +70 °C on filtered air.
Usually yes. Request a quote with the stroke and version and we will confirm whether it can be built, plus price and lead time.
No. You can order a single HLS12. Orders are processed and handed to the carrier within 3-5 business days.
Buying the HLS12 from AirtacDistr
Genuine AirTAC parts
Every order code on this page is the AirTAC factory part number. Specifications follow the AirTAC Products Catalog 2026A. About us
Ready in 3-5 business days
That is our time to process the order and hand it to the carrier. No minimum order: a single piece can be ordered.
14-day returns, 1-year warranty
Return within 14 days of delivery; the buyer pays return shipping. The warranty covers defects not caused by misuse. Return policy
Engineering help
Send your application details and we will confirm the right order code, usually within 7-8 hours. Ask us
Page data checked against the live catalog on 2026-10-30.
Request a Quote for the HLS12
Send the order code, quantity and destination. We confirm price, stock and lead time, usually within 7-8 hours.