AirTAC TMICL25 Guided Mini Cylinder, 25 mm Bore
Every AirTAC TMICL25 configuration on one page: 16 stock order codes with strokes from 25 to 250 mm, from $143.99. Pick a stroke, port thread and version to see the exact order code and price.
PT ports
This combination is not a stock order code. Request a quote and we will confirm availability and price.
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC TMICL25
The AirTAC TMICL25 is a double-acting mini cylinder combined with a twin-rod guide unit (adjustable cushions, linear ball bearings) with a 25 mm bore. At 0.5 MPa it pushes 245.4 N and pulls 206.2 N; at 0.7 MPa, 343.6 N push and 288.6 N pull. Force depends on bore and pressure only, so every stroke on this page gives the same output.
The guide unit's two rods run in linear ball bearings (L) for precise, low-friction travel; the body mounts in several directions. All TMICL25 versions use 1/8" air ports and run on filtered air at 0.15 to 1.0 MPa (proof 1.5 MPa), from -20 to +70 °C, at 30 to 500 mm/s. This page lists 16 stock order codes with strokes from 25 to 250 mm; the catalog maximum stroke is 250 mm.
TMICL25 Technical Specifications
| Bore size | Ø25 mm |
|---|---|
| Piston rod | Ø10 mm |
| Stock strokes | 25 – 250 mm |
| Catalog maximum stroke | 250 mm |
| Port size | 1/8" (PT standard) |
| Fluid | Air (filtered by 40 µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Adjustable air cushion |
| Guide bearing | Linear ball bearing (L) |
Source: AirTAC Products Catalog 2026A (PDF01-P0431/P0432), TMI/TMIC series ordering code and specifications.
Theoretical output force (Ø25 mm)
| Pressure | Push | Pull |
|---|---|---|
| 0.5 MPa | 245.4 N | 206.2 N |
| 0.7 MPa | 343.6 N | 288.6 N |
Push = pressure × bore area; pull subtracts the Ø10 mm rod area. Usable force is lower because of friction and back-pressure.
How the TMICL25 Order Code Is Built
| TMICL25 | Series and bore (25 mm) |
|---|---|
| X50 | Stroke in mm |
| S | Built-in magnet for position sensors (blank = none) |
| G | Port thread: G = G (BSPP), blank = PT |
All AirTAC TMICL25 Order Codes (16)
Each order code links to its own datasheet page. Use Select to load it into the configurator above.
| Order code | Stroke (mm) | Port thread | Magnet | Price | Select |
|---|---|---|---|---|---|
| TMICL25X25S | 25 mm | PT ports | Magnet (S) | $145.85 | |
| TMICL25X25 | 25 mm | PT ports | No magnet | $143.99 | |
| TMICL25X50S | 50 mm | PT ports | Magnet (S) | $149.31 | |
| TMICL25X50 | 50 mm | PT ports | No magnet | $147.45 | |
| TMICL25X75S | 75 mm | PT ports | Magnet (S) | $153.04 | |
| TMICL25X75 | 75 mm | PT ports | No magnet | $151.18 | |
| TMICL25X100S | 100 mm | PT ports | Magnet (S) | $156.76 | |
| TMICL25X100 | 100 mm | PT ports | No magnet | $154.90 | |
| TMICL25X125S | 125 mm | PT ports | Magnet (S) | $160.28 | |
| TMICL25X125 | 125 mm | PT ports | No magnet | $158.41 | |
| TMICL25X150S | 150 mm | PT ports | Magnet (S) | $164.00 | |
| TMICL25X150 | 150 mm | PT ports | No magnet | $162.14 | |
| TMICL25X200S | 200 mm | PT ports | Magnet (S) | $171.18 | |
| TMICL25X200 | 200 mm | PT ports | No magnet | $169.32 | |
| TMICL25X250S | 250 mm | PT ports | Magnet (S) | $178.63 | |
| TMICL25X250 | 250 mm | PT ports | No magnet | $176.77 |
Need a combination that is not listed? Request a quote.
Where the TMICL25 Is Used
Guided pushers
About 245.4 N at 0.5 MPa with the load carried by the guide rods.
Lifting small tooling
The guide rods stop rotation and take side load.
Sensed positioning
Magnet versions report stroke ends through cylinder sensors.
Choosing the Right TMICL25 Configuration
Start with the stroke. Pick the exact travel your machine needs; a longer stroke adds length and air consumption without adding force. If your length is not listed, request a quote and we will confirm whether it can be built.
Finally pick the version: S adds a magnet for position sensors.
AirTAC TMICL25 FAQ
No. Every TMICL25 gives about 245.4 N push and 206.2 N pull at 0.5 MPa, whatever the stroke.
1/8" ports, PT thread as standard.
0.15 to 1.0 MPa operating pressure (proof 1.5 MPa), 30 to 500 mm/s and -20 to +70 °C on filtered air.
Usually yes. Request a quote with the stroke and version and we will confirm whether it can be built, plus price and lead time.
No. You can order a single TMICL25. Orders are processed and handed to the carrier within 3-5 business days.
Buying the TMICL25 from AirtacDistr
Genuine AirTAC parts
Every order code on this page is the AirTAC factory part number. Specifications follow the AirTAC Products Catalog 2026A. About us
Ready in 3-5 business days
That is our time to process the order and hand it to the carrier. No minimum order: a single piece can be ordered.
14-day returns, 1-year warranty
Return within 14 days of delivery; the buyer pays return shipping. The warranty covers defects not caused by misuse. Return policy
Engineering help
Send your application details and we will confirm the right order code, usually within 7-8 hours. Ask us
Page data checked against the live catalog on 2026-10-30.
Request a Quote for the TMICL25
Send the order code, quantity and destination. We confirm price, stock and lead time, usually within 7-8 hours.