AirTAC TCL50 Guided Air Cylinder, 50 mm Bore
Every AirTAC TCL50 configuration on one page: 21 stock order codes with strokes from 25 to 250 mm, from $171.86. Pick a stroke, port thread and version to see the exact order code and price.
PT ports
Magnet (S)
This combination is not a stock order code. Request a quote and we will confirm availability and price.
- No minimum order. A single piece can be ordered.
- Ready in 3–5 business days. That is the time we take to process the order and hand it to the carrier. Transit time after that depends on the destination.
About the AirTAC TCL50
The AirTAC TCL50 is a double-acting three-rod guided cylinder (linear-bearing guides) with a 50 mm bore. At 0.5 MPa it pushes 981.7 N and pulls 824.7 N; at 0.7 MPa, 1374.4 N push and 1154.5 N pull. Force depends on bore and pressure only, so every stroke on this page gives the same output.
Two guide rods run in linear ball bearings (L) for smooth, precise travel; the body mounts from the top, rear or underside. All TCL50 versions use 1/4" air ports and run on filtered air at 0.15 to 1.0 MPa (proof 1.5 MPa), from -20 to +70 °C, at 30 to 500 mm/s. This page lists 21 stock order codes with strokes from 25 to 250 mm; the catalog maximum stroke is 250 mm.
TCL50 Technical Specifications
| Bore size | Ø50 mm |
|---|---|
| Piston rod | Ø20 mm |
| Stock strokes | 25 – 250 mm |
| Catalog maximum stroke | 250 mm |
| Port size | 1/4" (PT standard) |
| Fluid | Air (filtered by 40 µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Rubber bumpers at both ends |
| Guide bearing | Linear ball bearing (L) |
Source: AirTAC Products Catalog 2026A (PDF01-P0522/P0523), TC (TCL/TCM) series ordering code and specifications.
Theoretical output force (Ø50 mm)
| Pressure | Push | Pull |
|---|---|---|
| 0.5 MPa | 981.7 N | 824.7 N |
| 0.7 MPa | 1374.4 N | 1154.5 N |
Push = pressure × bore area; pull subtracts the Ø20 mm rod area. Usable force is lower because of friction and back-pressure.
How the TCL50 Order Code Is Built
| TCL50 | Series and bore (50 mm) |
|---|---|
| X50 | Stroke in mm |
| S | Built-in magnet for position sensors (every code) |
| G / T | Port thread: G = G (BSPP), T = NPT, blank = PT |
All AirTAC TCL50 Order Codes (21)
Each order code links to its own datasheet page. Use Select to load it into the configurator above.
| Order code | Stroke (mm) | Port thread | Magnet | Price | Select |
|---|---|---|---|---|---|
| TCL50X25-S | 25 mm | PT ports | Magnet (S) | $171.86 | |
| TCL50X30-S | 30 mm | PT ports | Magnet (S) | $174.44 | |
| TCL50X35S | 35 mm | PT ports | Magnet (S) | $179.56 | |
| TCL50X40-S | 40 mm | PT ports | Magnet (S) | $179.61 | |
| TCL50X45S | 45 mm | PT ports | Magnet (S) | $184.94 | |
| TCL50X50-S | 50 mm | PT ports | Magnet (S) | $184.78 | |
| TCL50X55S | 55 mm | PT ports | Magnet (S) | $201.68 | |
| TCL50X60-S | 60 mm | PT ports | Magnet (S) | $201.84 | |
| TCL50X65S | 65 mm | PT ports | Magnet (S) | $207.27 | |
| TCL50X70-S | 70 mm | PT ports | Magnet (S) | $207.01 | |
| TCL50X75-S | 75 mm | PT ports | Magnet (S) | $210.11 | |
| TCL50X80-S | 80 mm | PT ports | Magnet (S) | $212.70 | |
| TCL50X85S | 85 mm | PT ports | Magnet (S) | $217.97 | |
| TCL50X90-S | 90 mm | PT ports | Magnet (S) | $217.87 | |
| TCL50X100-S | 100 mm | PT ports | Magnet (S) | $223.55 | |
| TCL50X125-S | 125 mm | PT ports | Magnet (S) | $245.27 | |
| TCL50X150-S | 150 mm | PT ports | Magnet (S) | $260.26 | |
| TCL50X175-S | 175 mm | PT ports | Magnet (S) | $277.32 | |
| TCL50X200-S | 200 mm | PT ports | Magnet (S) | $293.34 | |
| TCL50X225-S | 225 mm | PT ports | Magnet (S) | $312.47 | |
| TCL50X250-S | 250 mm | PT ports | Magnet (S) | $330.05 |
Need a combination that is not listed? Request a quote.
Where the TCL50 Is Used
Pick-and-place and stoppers
Guide rods keep tooling square while the cylinder delivers about 981.7 N at 0.5 MPa.
Pushers with side load
The guide rods take side load that would wear a plain cylinder rod.
Lifting and transfer units
Mounts from the top, back or underside to fit compact stations.
Choosing the Right TCL50 Configuration
Start with the stroke. Pick the exact travel your machine needs; a longer stroke adds length and air consumption without adding force. If your length is not listed, request a quote and we will confirm whether it can be built.
Finally pick the version: every code carries a magnet for position sensors.
AirTAC TCL50 FAQ
No. Every TCL50 gives about 981.7 N push and 824.7 N pull at 0.5 MPa, whatever the stroke.
1/4" ports, PT thread as standard.
0.15 to 1.0 MPa operating pressure (proof 1.5 MPa), 30 to 500 mm/s and -20 to +70 °C on filtered air.
Usually yes. Request a quote with the stroke and version and we will confirm whether it can be built, plus price and lead time.
No. You can order a single TCL50. Orders are processed and handed to the carrier within 3-5 business days.
Buying the TCL50 from AirtacDistr
Genuine AirTAC parts
Every order code on this page is the AirTAC factory part number. Specifications follow the AirTAC Products Catalog 2026A. About us
Ready in 3-5 business days
That is our time to process the order and hand it to the carrier. No minimum order: a single piece can be ordered.
14-day returns, 1-year warranty
Return within 14 days of delivery; the buyer pays return shipping. The warranty covers defects not caused by misuse. Return policy
Engineering help
Send your application details and we will confirm the right order code, usually within 7-8 hours. Ask us
Page data checked against the live catalog on 2026-10-30.
Request a Quote for the TCL50
Send the order code, quantity and destination. We confirm price, stock and lead time, usually within 7-8 hours.