verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 3V1 · 3/2-Way Solenoid Valve

Airtac 3V1 Solenoid Valve 3V106FI4FT

The AirTAC 3V1 Solenoid Valve 3V106FI4FT is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.

  • Valve type3/2-way (3-port, 2-position)
  • Port size1/8 in
  • Coil voltageDC12V
  • Electrical entryFlying lead (lead-out wire type)
  • Stations4
  • Series3V1
$96.86 $104.36Save 7% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every 3V1-06 voltage, entry and configuration on one page All 3V1-06 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac 3V1 Solenoid Valve 3V106FI4FT

The 3V106FI4FT mounts four 3/2 direct-acting valve units on a single manifold base with 1/8in NPT ports, so a four-point air circuit takes one supply gallery instead of a panel of individually plumbed valves. Each unit is a three-port, two-state device: it feeds its outlet line or vents it to exhaust, the pattern that drives single-acting spring-return cylinders, blow nozzles, clamps and pilot stages.

Every station carries its own DC12V coil drawing 2.5 W and a pre-wired flying lead instead of a DIN socket, so low-voltage wiring lands on the terminal strip directly. IP65 (DIN 40050) sealing, a manual override on each valve and spring return complete the package. Request a quotation for genuine AirTAC valves with your exact station count.

Airtac 3V1 Solenoid Valve 3V106FI4FT Technical Specifications

ModelAirtac 3V1 Solenoid Valve 3V106FI4FT
Series3V1
Valve type3/2-way (3-port, 2-position)
FunctionDirect-acting, single solenoid, spring return
Port size1/8 in
ThreadNPT
Coil voltageDC12V
Electrical entryFlying lead (lead-out wire type)
Coil power2.5 W
Operating pressure0-0.8 MPa (0-114 psi)
Vacuum serviceNot rated for vacuum
Flow coefficientNot published for 3V1
Temperature-20 to 70 C
ConstructionDirect-acting, single solenoid, spring return
ProtectionIP65 (DIN 40050)
MediumAir, filtered by a 40 µm or finer element. Lubrication not required.

Figures follow the official AirTAC 3V1 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.

3V1 has no published flow coefficient. There is no Cv and no effective-area figure for this body in the source, so we do not print one. If the duty is flow-critical, ask us and we will confirm it, or step up to 3V2 (Cv 0.18-0.19) or 3V3 (Cv 0.62).

Model Code: Airtac 3V1 Solenoid Valve 3V106FI4FT

3V1Body — sets the flow, the coil power and whether vacuum is rated.
1/8 inPort size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in.
DC12VCoil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V.
IElectrical entry: I = flying lead, otherwise a DIN plug.
4F4 stations in one assembly.
NPTPort thread. PT is standard; G and NPT are available to order.

What a 3/2 Valve Does

A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.

That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.

It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.

Where the Airtac 3V1 Solenoid Valve 3V106FI4FT Is Used

build

AGV transfer-cart clamps

Four spring-return clamp cylinders on a battery-powered AGV grip and release the load; each 12 V station draws only 2.5 W, so the traction battery is barely touched.

science

Benchtop soil-sampling probe array

A lab sampling rig vents its small single-acting probe cylinders and purge lines through four valves that share one 1/8in NPT manifold base.

air

Optics lens-dusting nozzles

An inspection cell fires short air pulses across glass lenses; the direct-acting 3/2 units feed or vent each nozzle and the spring return isolates the outlet whenever the coil drops out.

Is the Airtac 3V1 Solenoid Valve 3V106FI4FT the Right Part?

The 3V1 is the smallest, lowest-power body in AirTAC's 3V range and its flow coefficient is not published, so any flow-critical duty should be checked with us first. When four stations still do not give enough flow per line, step up to 3V2 (1/8in and 1/4in, NC or NO selectable, Cv 0.18-0.19, vacuum rated) or 3V3 (1/4in, Cv 0.62); if manifold density matters more than flow, 3V2M is the alternative worth comparing.

Before ordering, match five points: port (M5 or 1/8in), thread (NPT on this code), coil voltage, electrical entry (DIN plug or flying lead), and individual valve versus manifold station count. Need to drive a double-acting cylinder? That requires a 5-port valve - go to the AirTAC 4V series.

Confirm before you order

  • ✓ Port size and thread (PT standard; G / NPT to order)
  • ✓ Coil voltage matches your controller output
  • ✓ Electrical entry — DIN plug or flying lead
  • ✓ Single valve, bare base, or complete assembly
  • ✓ Single-acting duty, not double-acting
Ask an Engineer

Installation & Wiring Notes

  • check Use clean air filtered to 40µm or finer.
  • check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
  • check Match the coil voltage to your controller output.
  • check Use the manual override to test before powering up.
  • check Leave the exhaust port clear, or fit a silencer.
  • check Blank any unused station on the base before pressurising.
  • check Wiring by qualified personnel, per AirTAC documentation.

Airtac 3V1 Solenoid Valve 3V106FI4FT FAQ

Operating pressure 0-0.8 MPa (0-114 psi); media temperature -20 to 70 C; coil power AC220V 4.5 VA, AC110V 4.5 VA, AC24V 5.0 VA, DC24V 3.0 W, DC12V 2.5 W (this model uses the 2.5 W DC12V coil); protection IP65 to DIN 40050; air filtered to 40 um or finer, no lubrication required. No flow coefficient (Cv) is published for the 3V1 - confirm flow-critical sizing with us.

Each 3/2 station has three ports and two states: it either supplies the outlet or exhausts it. That suits single-acting spring-return cylinders, blow-off jets, clamping devices and pilot duty on larger valves. It cannot run a double-acting cylinder - that needs a 5-port valve such as the AirTAC 4V. A manual override on every station helps during setup.

T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.

verified

Authorized Export Seller

Genuine AirTAC parts produced by the AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Request a Quote for Airtac 3V1 Solenoid Valve 3V106FI4FT

Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for 3V106FI4FT and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.