verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 3V1 · 3/2-Way Solenoid Valve

Airtac 3V1 Solenoid Valve 3V106FIT

The AirTAC 3V1 Solenoid Valve 3V106FIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/8 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.

  • Valve type3/2-way (3-port, 2-position)
  • Port size1/8 in
  • Coil voltageDC12V
  • Electrical entryFlying lead (lead-out wire type)
  • Series3V1
$24.11 $31.61Save 23% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every 3V1-06 voltage, entry and configuration on one page All 3V1-06 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac 3V1 Solenoid Valve 3V106FIT

The AirTAC 3V106FIT is the DC12V, flying-lead version of the smallest 3V1 valve: a 3/2-way, direct-acting unit with a single solenoid and spring return. It either feeds or vents one line, which makes it the natural switch for single-acting cylinders, air blow-off, clamps or a pilot signal to a larger valve. The NPT1/8 port keeps the plumbing compact, and the 2.5 W coil suits battery-backed and low-power 12 V controls.

Instead of a DIN socket, this entry carries pre-attached lead-out wires, so the coil wires straight into your 12 V cabinet or harness. The coil is protected to IP65 (DIN 40050) and a manual override is fitted for set-up and fault finding. Air is the only medium; filter it to 40 um or finer and no lubrication is needed. This version has NPT ports (the T in the order code) for North American pipe fittings.

Airtac 3V1 Solenoid Valve 3V106FIT Technical Specifications

ModelAirtac 3V1 Solenoid Valve 3V106FIT
Series3V1
Valve type3/2-way (3-port, 2-position)
FunctionDirect-acting, single solenoid, spring return
Port size1/8 in
ThreadNPT
Coil voltageDC12V
Electrical entryFlying lead (lead-out wire type)
Coil power2.5 W
Operating pressure0-0.8 MPa (0-114 psi)
Vacuum serviceNot rated for vacuum
Flow coefficientNot published for 3V1
Temperature-20 to 70 C
ConstructionDirect-acting, single solenoid, spring return
ProtectionIP65 (DIN 40050)
MediumAir, filtered by a 40 µm or finer element. Lubrication not required.

Figures follow the official AirTAC 3V1 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.

3V1 has no published flow coefficient. There is no Cv and no effective-area figure for this body in the source, so we do not print one. If the duty is flow-critical, ask us and we will confirm it, or step up to 3V2 (Cv 0.18-0.19) or 3V3 (Cv 0.62).

Model Code: Airtac 3V1 Solenoid Valve 3V106FIT

3V1Body — sets the flow, the coil power and whether vacuum is rated.
1/8 inPort size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in.
DC12VCoil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V.
IElectrical entry: I = flying lead, otherwise a DIN plug.
NPTPort thread. PT is standard; G and NPT are available to order.

What a 3/2 Valve Does

A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.

That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.

It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.

Where the Airtac 3V1 Solenoid Valve 3V106FIT Is Used

local_shipping

Battery-powered service trucks

A DC12V coil runs straight from a vehicle battery, switching the air chuck or clamp line on mobile maintenance rigs without an inverter in the circuit.

science

Bench-top leak test rigs

QC benches built around 12 V logic use the valve to feed or vent the test line acting on a single spring-return cylinder, one part at a time.

cable

Pre-wired machine retrofits

The flying lead solders directly into older 12 V control cabinets, so older textile or packaging machines gain automatic blow-off without any DIN-rail rewiring.

Is the Airtac 3V1 Solenoid Valve 3V106FIT the Right Part?

3V1 is the smallest, lowest-power body in AirTAC's 3V range, and it publishes no Cv or effective area, so if your circuit lives or dies on flow, tell us the duty and we will confirm suitability before you order. When 1/8in is simply too small, step up to the 3V2 series (1/8in and 1/4in, NC or NO selectable, Cv 0.18-0.19 and rated for vacuum) or the 3V3 (1/4in, Cv 0.62); choose 3V2M where manifold density matters more than flow. Driving a double-acting cylinder is a job for the 5-port AirTAC 4V series, not this 3/2 valve.

Before ordering, match five points: port size (M5 or 1/8in), thread (NPT on this code), coil voltage (here DC12V at 2.5 W), electrical entry (flying lead on this SKU, DIN plug elsewhere), and whether you need an individual valve or a multi-station manifold.

Confirm before you order

  • ✓ Port size and thread (PT standard; G / NPT to order)
  • ✓ Coil voltage matches your controller output
  • ✓ Electrical entry — DIN plug or flying lead
  • ✓ Single valve, bare base, or complete assembly
  • ✓ Single-acting duty, not double-acting
Ask an Engineer

Installation & Wiring Notes

  • check Use clean air filtered to 40µm or finer.
  • check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
  • check Match the coil voltage to your controller output.
  • check Use the manual override to test before powering up.
  • check Leave the exhaust port clear, or fit a silencer.
  • check Wiring by qualified personnel, per AirTAC documentation.

Airtac 3V1 Solenoid Valve 3V106FIT FAQ

Operating pressure is 0-0.8 MPa (0-114 psi), media temperature -20 to 70 C, and the protection class IP65 (DIN 40050). The DC12V coil of this SKU draws 2.5 W; across the family AC220V and AC110V coils are 4.5 VA, AC24V 5.0 VA and DC24V 3.0 W. AirTAC publishes no Cv or effective area for 3V1, so flow figures must be confirmed case by case.

As a 3/2 valve it pressurises or exhausts a single outlet, so it suits spring-return single-acting cylinders, on/off air blow, clamping and pilot duty on larger valves. It cannot drive a double-acting cylinder - that requires a 5-port valve such as the AirTAC 4V series.

T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.

verified

Authorized Export Seller

Genuine AirTAC parts produced by the AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Request a Quote for Airtac 3V1 Solenoid Valve 3V106FIT

Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for 3V106FIT and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.