verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 3V2 · 3/2-Way Solenoid Valve

Airtac 3V2 Solenoid Valve 3V208NCFT

The AirTAC 3V2 Solenoid Valve 3V208NCFT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.

  • Valve type3/2-way (3-port, 2-position)
  • Initial stateNormally closed
  • Port size1/4 in
  • Coil voltageDC12V
  • Electrical entryDIN plug (DIN socket type)
  • Flow (Cv)0.19
  • Series3V2
$48.60 $56.10Save 13% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every 3V2-08 voltage, entry and configuration on one page All 3V2-08 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac 3V2 Solenoid Valve 3V208NCFT

3V208NCFT is the 12 V DC build of the AirTAC 3V2: a normally closed, direct-acting 3/2 poppet valve on a 1/4in NPT port. De-energised, it holds the outlet vented and the supply shut off, so no air reaches the line until the coil is powered. Spring return resets it the instant power drops. The coaxial shut-off poppet gives a clean seat at a per-port flow of 3.4 mm2 effective area, Cv 0.19.

The 7.0 W DC coil suits battery carts, mobile equipment and other sites where no 24 V or AC supply exists, and the DIN plug accepts a standard square connector. This body carries a vacuum rating of -102.2 kPa to 0.1 MPa, so the same valve can switch negative-pressure circuits too. Medium is air filtered to 40 um or finer; lubrication is not required.

Airtac 3V2 Solenoid Valve 3V208NCFT Technical Specifications

ModelAirtac 3V2 Solenoid Valve 3V208NCFT
Series3V2
Valve type3/2-way (3-port, 2-position)
FunctionDirect-acting, single solenoid, spring return
Initial stateNormally closed
Port size1/4 in
ThreadNPT
Coil voltageDC12V
Electrical entryDIN plug (DIN socket type)
Coil power7.0 W
Operating pressure0-0.8 MPa (0-114 psi)
Vacuum serviceRated -102.2 kPa to 0.1 MPa
Flow coefficientCv 0.19 (3.4 mm2 effective area)
Temperature-20 to 70 C
ConstructionCoaxial shut-off (poppet), direct-acting, spring return
ProtectionIP65 (DIN 40050)
MediumAir, filtered by a 40 µm or finer element. Lubrication not required.

Figures follow the official AirTAC 3V2 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.

Model Code: Airtac 3V2 Solenoid Valve 3V208NCFT

3V2Body — sets the flow, the coil power and whether vacuum is rated.
1/4 inPort size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in.
NCNormally closed: no air at the outlet until the coil is energised.
DC12VCoil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V.
—Electrical entry: I = flying lead, otherwise a DIN plug.
NPTPort thread. PT is standard; G and NPT are available to order.

What a 3/2 Valve Does

A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.

That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.

It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.

Where the Airtac 3V2 Solenoid Valve 3V208NCFT Is Used

cable

Battery-powered material handling

A 12 V lead-acid supply on an electric pallet-truck or utility cart runs the coil directly, so the valve can switch a spring-return clamp or blow line without an inverter.

air

Blow-off on a small parts feeder

Energise to open the supply to a 1/4in air nozzle that clears chips or dust from a fixture; de-energise and the NC poppet leaves the line dead and vented.

science

Vacuum hold-down on a bench-top router

Rated from -102.2 kPa to 0.1 MPa, the valve can isolate a vacuum chuck gripping plywood or acrylic, releasing the workpiece with the manual override during setup.

Is the Airtac 3V2 Solenoid Valve 3V208NCFT the Right Part?

Flow here is the per-port figure: Cv 0.19 (3.4 mm2) on this 1/4in body. Step down to 3V1 when the duty is small and every watt counts (its DC24V coil draws 3.0 W against 7.0 W here), or to 3V2M when a dense multi-station base matters more than flow (Cv 0.1 through the manifold). If the job genuinely needs more air, move up to 3V3: 1/4in, Cv 0.62 and also vacuum-rated. Confirm five points before ordering: port size and thread (1/8in or 1/4in; This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. A double-acting cylinder needs a 5-port valve - go to the AirTAC 4V series.

Confirm before you order

  • ✓ Port size and thread (PT standard; G / NPT to order)
  • ✓ Initial state — NC or NO, ordered up front
  • ✓ Coil voltage matches your controller output
  • ✓ Electrical entry — DIN plug or flying lead
  • ✓ Single valve, bare base, or complete assembly
  • ✓ Single-acting duty, not double-acting
Ask an Engineer

Installation & Wiring Notes

  • check Use clean air filtered to 40µm or finer.
  • check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
  • check Match the coil voltage to your controller output.
  • check Use the manual override to test before powering up.
  • check Leave the exhaust port clear, or fit a silencer.
  • check Wiring by qualified personnel, per AirTAC documentation.

Airtac 3V2 Solenoid Valve 3V208NCFT FAQ

This 1/4in port (3V208) flows 3.4 mm2 effective area, Cv 0.19 per port; the 1/8in 3V206 body is 3.2 mm2, Cv 0.18. Pressure range is 0-0.8 MPa, with vacuum service rated -102.2 kPa to 0.1 MPa. Temperature spans -20 to 70 C. Coils draw 7 VA on AC and 7.0 W on DC, and the housing meets IP65 (DIN 40050).

No. A 3/2 valve has three ports - supply, outlet, exhaust - and only ever feeds or vents one line, which suits single-acting spring-return cylinders, blow duty, clamps, vacuum switching and pilot stages. For a double-acting cylinder you need a 5-port valve from the AirTAC 4V series.

T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.

verified

Authorized Export Seller

Genuine AirTAC parts produced by the AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Request a Quote for Airtac 3V2 Solenoid Valve 3V208NCFT

Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for 3V208NCFT and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.