verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 3V2 · 3/2-Way Solenoid Valve

Airtac 3V2 Solenoid Valve 3V208NOFIT

The AirTAC 3V2 Solenoid Valve 3V208NOFIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.

  • Valve type3/2-way (3-port, 2-position)
  • Initial stateNormally open
  • Port size1/4 in
  • Coil voltageDC12V
  • Electrical entryFlying lead (lead-out wire type)
  • Flow (Cv)0.19
  • Series3V2
$48.60 $56.10Save 13% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every 3V2-08 voltage, entry and configuration on one page All 3V2-08 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac 3V2 Solenoid Valve 3V208NOFIT

The 3V208NOFIT pairs a DC12V coil with a pre-wired lead-out, the cleanest option for mobile and battery-powered builds where DIN plug hardware is not carried on site. Strip, land and seal the two wires and the valve is live.

As a normally open 3/2 valve it passes air from supply to outlet while unpowered and vents the outlet when the solenoid pulls in, driving single-acting cylinders, blow jets, clamps or pilot stages. The coaxial poppet seats sharply at Cv 0.19 (3.4 mm2 per port), and this body carries the 3V2 family's negative-pressure rating of -102.2 kPa to 0.1 MPa - a capability the 3V1 and 3V2M do not share. This version has NPT ports (the T in the order code) for North American pipe fittings.

Airtac 3V2 Solenoid Valve 3V208NOFIT Technical Specifications

ModelAirtac 3V2 Solenoid Valve 3V208NOFIT
Series3V2
Valve type3/2-way (3-port, 2-position)
FunctionDirect-acting, single solenoid, spring return
Initial stateNormally open
Port size1/4 in
ThreadNPT
Coil voltageDC12V
Electrical entryFlying lead (lead-out wire type)
Coil power7.0 W
Operating pressure0-0.8 MPa (0-114 psi)
Vacuum serviceRated -102.2 kPa to 0.1 MPa
Flow coefficientCv 0.19 (3.4 mm2 effective area)
Temperature-20 to 70 C
ConstructionCoaxial shut-off (poppet), direct-acting, spring return
ProtectionIP65 (DIN 40050)
MediumAir, filtered by a 40 µm or finer element. Lubrication not required.

Figures follow the official AirTAC 3V2 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.

Model Code: Airtac 3V2 Solenoid Valve 3V208NOFIT

3V2Body — sets the flow, the coil power and whether vacuum is rated.
1/4 inPort size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in.
NONormally open: air passes until the coil is energised.
DC12VCoil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V.
IElectrical entry: I = flying lead, otherwise a DIN plug.
NPTPort thread. PT is standard; G and NPT are available to order.

What a 3/2 Valve Does

A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.

That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.

It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.

Where the Airtac 3V2 Solenoid Valve 3V208NOFIT Is Used

engineering

Mobile robot vacuum gripper

On an AMR fitted with a suction gripper, the pre-wired DC12V lead connects straight to the robot's battery rail, and the NO state keeps the vacuum path open if control power is ever lost.

shield

Emergency vent on a pneumatic door lock

Wired so that losing 12 V leaves the vent path open, the valve dumps a fire-exit door-lock cylinder to exhaust during a power failure, keeping the escape-route release on the safe side.

build

Solar-powered clamp cart

A battery-and-solar workshop cart runs its vacuum clamp grid through this valve; the DC12V coil matches the cart's electrical system and the flying lead removes any need for connector hardware.

Is the Airtac 3V2 Solenoid Valve 3V208NOFIT the Right Part?

Before ordering, lock in: port 1/4in (NPT on this code), NO initial state, DC12V voltage, flying-lead entry, and whether vacuum is in the circuit. Downsize to 3V1 when the task is small and every watt counts (3.0 W on DC24V there versus 7.0 W here) or to 3V2M when a manifold beats individual plumbing but flow can drop to Cv 0.1. Upsize to 3V3 (Cv 0.62, vacuum rated) when the flow coefficient must climb well past 0.19. For a double-acting cylinder, switch to the AirTAC 4V series - a 3/2 valve cannot reverse one.

Confirm before you order

  • ✓ Port size and thread (PT standard; G / NPT to order)
  • ✓ Initial state — NC or NO, ordered up front
  • ✓ Coil voltage matches your controller output
  • ✓ Electrical entry — DIN plug or flying lead
  • ✓ Single valve, bare base, or complete assembly
  • ✓ Single-acting duty, not double-acting
Ask an Engineer

Installation & Wiring Notes

  • check Use clean air filtered to 40µm or finer.
  • check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
  • check Match the coil voltage to your controller output.
  • check Use the manual override to test before powering up.
  • check Leave the exhaust port clear, or fit a silencer.
  • check Wiring by qualified personnel, per AirTAC documentation.

Airtac 3V2 Solenoid Valve 3V208NOFIT FAQ

The 1/4in body passes Cv 0.19 per port with a 3.4 mm2 effective area; the smaller 3V206 (1/8in) is Cv 0.18 / 3.2 mm2. Pressure spans 0-0.8 MPa with vacuum service allowed at -102.2 kPa to 0.1 MPa. Operating temperature is -20 to 70 C. AC coils use 7 VA and DC coils 7.0 W, the housing meets IP65 (DIN 40050), and the air supply needs filtration of 40 um or finer.

The lead-out suits battery-powered and mobile equipment where DIN connectors are not on hand; the wires land straight into a fuse box or terminal strip. Functionally nothing changes: normally open, direct acting, spring return, Cv 0.19 on 1/4in NPT ports, vacuum rated to -102.2 kPa. For NC, other voltages or a DIN plug, the same body is available in those options.

T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.

verified

Authorized Export Seller

Genuine AirTAC parts produced by the AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Request a Quote for Airtac 3V2 Solenoid Valve 3V208NOFIT

Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for 3V208NOFIT and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.