
The AirTAC 3V3 Solenoid Valve 3V308NCBIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
In the 3V308NCBIT the 6.5 W DC24V coil arrives pre-wired on a flying lead, ready to land on a 24 V terminal block with no DIN plug to source. The valve itself is a normally closed, direct-acting 3/2 coaxial poppet on a 1/4in NPT thread, feeding or venting a single line under spring return.
The DC figure rewards attention: 6.5 W is actually lower than the 7.0 W of the smaller 3V2 body, even though this valve moves far more air through its Cv 0.62 orifice. That makes it an efficient pick for 24 V panels driving bigger single-acting cylinders or blow-off nozzles.
| Model | Airtac 3V3 Solenoid Valve 3V308NCBIT |
|---|---|
| Series | 3V3 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally closed |
| Port size | 1/4 in |
| Thread | NPT |
| Coil voltage | DC24V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 6.5 W |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Rated -102.2 kPa to 0.1 MPa |
| Flow coefficient | Cv 0.62 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), direct-acting, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V3 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| 3V3 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NC | Normally closed: no air at the outlet until the coil is energised. |
| DC24V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| NPT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Releases or locks a spring-return latch cylinder from the vehicle's 24 V system, with the lead-out wire spliced straight into the chassis harness.
De-energising the NC coil vents a clamping circuit to exhaust, giving a defined fail-safe state that survives a control power failure.
Feeds a larger spring-return ram from a 24 V panel; the Cv 0.62 flow path shortens stroke time compared with the smaller 3V2 bodies.
Step down from this high-flow body when Cv 0.62 is more than the job needs: 3V2 (Cv 0.18-0.19, also rated for vacuum), 3V2M (Cv 0.1) for compact manifold banks, or 3V1 where the lowest DC power wins. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Driving a double-acting cylinder? Specify the 5-port AirTAC 4V range.
Confirm before you order
Cv 0.62 (a coefficient, not a flow rate), operating pressure 0-0.8 MPa, vacuum rating -102.2 kPa to 0.1 MPa, temperature -20 to 70 C, DC24V coil drawing 6.5 W versus 10 VA on AC variants, IP65 protection, and air filtered to 40 um or better. Manual override is standard.
Flow: Cv 0.62 here versus 0.18-0.19 on 3V2 and 0.1 on 3V2M, roughly six times a 3V2M, yet the 6.5 W DC24V coil still sits below 3V2's 7.0 W. Use it for larger single-acting loads; double-acting cylinders belong on the 5-port 4V series.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.