verified AirTAC China Authorized Export Seller shield 100% Genuine AirTAC Parts workspace_premium 1-Year Warranty
appsShop by Modelexpand_more
person shopping_cart Request a QuoteQuote
AirTAC 3V3 · 3/2-Way Solenoid Valve

Airtac 3V3 Solenoid Valve 3V308NCEIT

The AirTAC 3V3 Solenoid Valve 3V308NCEIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.

  • Valve type3/2-way (3-port, 2-position)
  • Initial stateNormally closed
  • Port size1/4 in
  • Coil voltageAC24V
  • Electrical entryFlying lead (lead-out wire type)
  • Flow (Cv)0.62
  • Series3V3
$65.76 $73.26Save 10% Standard model — usually dispatched in 3-5 days
Request a Quote
  • No minimum order. A single piece can be ordered.
  • Shipped from our own warehouse: most standard models dispatch in 3–5 days; custom and non-standard models take 8–10 business days. Transit time after that depends on the destination.
Compare every 3V3-08 voltage, entry and configuration on one page All 3V3-08 codes →
verified Genuine AirTAC workspace_premium 1-year warranty bolt Reply in 7 h

About the Airtac 3V3 Solenoid Valve 3V308NCEIT

3V308NCEIT is specified around its wiring: the AC24V coil leaves the factory on a flying lead, a pre-attached lead-out that removes the separate DIN connector from the bill of materials on machines where every valve is hard-wired anyway. On air, it is a normally closed 3/2 valve - supply, outlet, exhaust - with the outlet held closed by the spring and the coaxial poppet until the 10 VA coil pulls it open.

The body itself is the highest-flow 3-port unit AirTAC lists at Cv 0.62, and its sealing approach suits negative-pressure work: the valve is rated for vacuum duty from -102.2 kPa up to 0.1 MPa. Temperature envelope is -20 to 70 C, and the IP65 (DIN 40050) build keeps dust and splashes off the coil. This version has NPT ports (the T in the order code) for North American pipe fittings.

Airtac 3V3 Solenoid Valve 3V308NCEIT Technical Specifications

ModelAirtac 3V3 Solenoid Valve 3V308NCEIT
Series3V3
Valve type3/2-way (3-port, 2-position)
FunctionDirect-acting, single solenoid, spring return
Initial stateNormally closed
Port size1/4 in
ThreadNPT
Coil voltageAC24V
Electrical entryFlying lead (lead-out wire type)
Coil power10 VA
Operating pressure0-0.8 MPa (0-114 psi)
Vacuum serviceRated -102.2 kPa to 0.1 MPa
Flow coefficientCv 0.62
Temperature-20 to 70 C
ConstructionCoaxial shut-off (poppet), direct-acting, spring return
ProtectionIP65 (DIN 40050)
MediumAir, filtered by a 40 µm or finer element. Lubrication not required.

Figures follow the official AirTAC 3V3 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.

Model Code: Airtac 3V3 Solenoid Valve 3V308NCEIT

3V3Body — sets the flow, the coil power and whether vacuum is rated.
1/4 inPort size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in.
NCNormally closed: no air at the outlet until the coil is energised.
AC24VCoil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V.
IElectrical entry: I = flying lead, otherwise a DIN plug.
NPTPort thread. PT is standard; G and NPT are available to order.

What a 3/2 Valve Does

A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.

That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.

It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.

Where the Airtac 3V3 Solenoid Valve 3V308NCEIT Is Used

local_shipping

Carton pick head on a case erector

Applies and releases vacuum to a wide multi-cup head that lifts flat corrugated blanks, with the poppet sealing reliably at -102.2 kPa and direct lead wiring to the machine harness.

engineering

Gripper on a palletising arm

Controls a spring-return gripper finger on a palletiser, where the NC state keeps the grip released and vented whenever the 24V AC control signal drops.

handyman

Fixture purge and hold on a weld cell

Feeds a hold-down cylinder and purge jet in a robotic weld cell, wired point-to-point on its flying lead and protected to IP65 against weld-spatter dust.

Is the Airtac 3V3 Solenoid Valve 3V308NCEIT the Right Part?

This is the top of AirTAC's 3-port ladder, so look down the range when the duty is smaller. 3V2 (Cv 0.18-0.19, also vacuum-rated) covers lighter lines, 3V2M (Cv 0.1) suits a crowded multi-station manifold where flow is not the constraint, and 3V1 handles the smallest low-power jobs (3.0 W on DC24V). Line up five parameters when ordering: port and thread (NPT on this code), initial state (NC on this code), coil voltage (AC24V), electrical entry (flying lead, not DIN plug), and whether vacuum appears anywhere in the duty. A double-acting cylinder belongs on a 5-port 4V valve, not here.

Confirm before you order

  • ✓ Port size and thread (PT standard; G / NPT to order)
  • ✓ Initial state — NC or NO, ordered up front
  • ✓ Coil voltage matches your controller output
  • ✓ Electrical entry — DIN plug or flying lead
  • ✓ Single valve, bare base, or complete assembly
  • ✓ Single-acting duty, not double-acting
Ask an Engineer

Installation & Wiring Notes

  • check Use clean air filtered to 40µm or finer.
  • check Stay within 0-0.8 MPa (0-114 psi) operating pressure.
  • check Match the coil voltage to your controller output.
  • check Use the manual override to test before powering up.
  • check Leave the exhaust port clear, or fit a silencer.
  • check Wiring by qualified personnel, per AirTAC documentation.

Airtac 3V3 Solenoid Valve 3V308NCEIT FAQ

Cv 0.62 flow coefficient, pressure range 0-0.8 MPa (0-114 psi), vacuum rating -102.2 kPa to 0.1 MPa, temperature -20 to 70 C, coil power 10 VA (AC) or 6.5 W (DC), protection class IP65 (DIN 40050). It is a direct-acting, single-solenoid 3/2 valve with spring return on a 1/4in NPT port; the air supply should pass a 40 um or finer filter, with no lubrication required.

The I suffix replaces the DIN socket with a factory-fitted lead-out wire, so the coil is wired straight into the machine's control cabinet without buying or keeping separate DIN plugs. It makes sense on OEM machines and cells where every solenoid is hard-wired; if your panel prefers plug-in coils and quick swap-outs, the plain 3V308NCE with its DIN plug is the better match.

T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.

verified

Authorized Export Seller

Genuine AirTAC parts produced by the AirTAC factory.

workspace_premium

1-Year Warranty

Covers non-human-caused product damage.

local_shipping

Fast Dispatch

Most standard models are dispatched in 3-5 days.

bolt

Fast Reply

Most inquiries answered within 7 hours.

Request a Quote for Airtac 3V3 Solenoid Valve 3V308NCEIT

Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.

Thank you. We received your request for 3V308NCEIT and will confirm price, availability and lead time — usually within 7 hours.

For the fastest response, keep the complete model number above and include a clear photo of the product label. If photo upload is unavailable, email photos to [email protected] with your model number.