
The AirTAC 3V3 Solenoid Valve 3V308NOBIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
The 3V308NOBIT runs on a DC24V coil that draws just 6.5 W - lower than the 7.0 W of the smaller 3V2, an asymmetry worth knowing when panel power is budgeted. The coil arrives on a flying lead, and the poppet is normally open: air flows until the coil energises, then the spring return vents the 1/4 inch NPT outlet.
Direct-acting and single-solenoid, it switches with a Cv 0.62 coefficient - the top of the 3V range - and handles vacuum duty down to -102.2 kPa, all backed by a genuine AirTAC build.
| Model | Airtac 3V3 Solenoid Valve 3V308NOBIT |
|---|---|
| Series | 3V3 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally open |
| Port size | 1/4 in |
| Thread | NPT |
| Coil voltage | DC24V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 6.5 W |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Rated -102.2 kPa to 0.1 MPa |
| Flow coefficient | Cv 0.62 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), direct-acting, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V3 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| 3V3 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NO | Normally open: air passes until the coil is energised. |
| DC24V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| NPT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
A venturi ejector serving palletiser vacuum cups is switched through this valve, which is rated for negative pressure from -102.2 kPa to 0.1 MPa.
Inflating the rubber seat that locates a sack in a carton needs the full Cv 0.62 passage so the bag fills fast under DC24V machine control.
At a remote gas wellhead skid, the 6.5 W coil and glanded lead-out cable suit a DC24V solar-battery bus with no spare DIN terminals.
Since 3V3 tops the range at Cv 0.62, any change of body means going smaller: 3V2 at Cv 0.18-0.19 for 1/8 inch circuits, 3V2M at Cv 0.1 when manifold station density outranks flow, or 3V1 for minimal draw at 3.0 W on DC24V. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Double-acting cylinders want five ports, so route those to the AirTAC 4V series.
Confirm before you order
Cv 0.62; operating pressure 0-0.8 MPa (0-114 psi); vacuum service from -102.2 kPa to 0.1 MPa; temperature -20 to 70 C; coil power 10 VA on AC models and 6.5 W on this DC24V version; IP65 (DIN 40050). Filter the air to 40 um or finer; lubrication is not required.
Normally open (this code) keeps the outlet fed while the coil is off and vents it when powered - right for purge, safety-dump and continuous-blow circuits; normally closed behaves the opposite way. The DC choice also matters: 3V3's 6.5 W draw undercuts 3V2's 7.0 W, while its AC coils take 10 VA, the highest in the range.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.