
The AirTAC 3V3 Solenoid Valve 3V308NOCT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
The 3V308NOCT is a normally open, 3/2-way solenoid valve with a 1/4 inch NPT port and an AC110V coil on a DIN plug. Air flows from supply to outlet until the coil is energised; de-energising, or a loss of control power, vents the outlet to exhaust. It drives single-acting cylinders, blow nozzles, clamps, vacuum lines and pilot stages — not double-acting cylinders, which need a 5-port 4V valve.
Flow is the headline: the coaxial poppet design gives a Cv of 0.62, the highest in AirTAC's 3V range and more than three times the 0.19 of a 3V208, so stepping up from a 3V2 body is a genuine jump in capacity. The valve is direct-acting with spring return, needs no minimum pressure to shift, carries a manual override for commissioning, and is rated for vacuum from -102.2 kPa to 0.1 MPa.
| Model | Airtac 3V3 Solenoid Valve 3V308NOCT |
|---|---|
| Series | 3V3 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally open |
| Port size | 1/4 in |
| Thread | NPT |
| Coil voltage | AC110V |
|---|---|
| Electrical entry | DIN plug (DIN socket type) |
| Coil power | 10 VA |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Rated -102.2 kPa to 0.1 MPa |
| Flow coefficient | Cv 0.62 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), direct-acting, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V3 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| 3V3 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NO | Normally open: air passes until the coil is energised. |
| AC110V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| — | Electrical entry: I = flying lead, otherwise a DIN plug. |
| NPT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Feeds a wide air knife that sweeps swarf off a machining-table part; being normally open, the blast stays on during normal running and a jam sensor can kill it by energising the coil.
Runs a high-volume drying nozzle ahead of a labelling station; Cv 0.62 gives the headroom for a broad slit, and energising the valve stops the blast between batches.
Holds vacuum on a cup array lifting glass or steel sheet; the normally open path keeps the part gripped through a control-power loss, and energising releases it.
3V3 is the largest 3-port body AirTAC makes, so the only sizing decision is downward. If Cv 0.62 is more than the duty needs, step to a 3V2 valve (1/8 or 1/4 port, Cv 0.18-0.19, also vacuum-rated); to a 3V2M (Cv 0.1) where a dense multi-station manifold matters more than flow; or to a 3V1 for the smallest duties (3.0 W on DC24V). This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. For a double-acting cylinder, move to the AirTAC 4V series.
Confirm before you order
Flow coefficient Cv 0.62, working pressure 0-0.8 MPa, vacuum rating -102.2 kPa to 0.1 MPa, media and ambient temperature -20 to 70 C, AC coil power 10 VA (the DC builds in this family draw 6.5 W), IP65 protection to DIN 40050, 1/4 inch NPT port, 3/2-way normally open function.
Choose NO when the outlet should stay fed while the coil is off, so a power failure leaves the machine in its running state and energising the coil stops the flow and vents the line. Choose NC when the outlet must be dead until the coil energises. Both states are orderable in the 3V3 family.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.