
The AirTAC 3V3 Solenoid Valve 3V308NOEIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
Circuits that run below atmospheric pressure are where the 3V308NOEIT earns its place: the same body that takes 0-0.8 MPa of compressed air is rated for vacuum service from -102.2 kPa to 0.1 MPa. It is a normally open 3/2 valve, so the 1/4 inch NPT port passes air or vacuum from supply to outlet at rest, and the energised AC24V coil shuts the path and vents the line.
The coil comes on a flying lead for direct harness connection rather than a DIN socket. Direct-acting, spring-return and built around a coaxial poppet, it delivers a Cv of 0.62 — the highest in the 3V range — which pays off with larger vacuum cups and longer eject lines. IP65 coil protection (DIN 40050) keeps it sealed in washdown-prone cells.
| Model | Airtac 3V3 Solenoid Valve 3V308NOEIT |
|---|---|
| Series | 3V3 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally open |
| Port size | 1/4 in |
| Thread | NPT |
| Coil voltage | AC24V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 10 VA |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Rated -102.2 kPa to 0.1 MPa |
| Flow coefficient | Cv 0.62 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), direct-acting, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V3 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| 3V3 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NO | Normally open: air passes until the coil is energised. |
| AC24V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| NPT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
Switches vacuum to a large suction cup on a pick-and-place gantry; the normally open path holds the part if control power is lost, and energising the coil releases it in a controlled vent.
Feeds one zone of a multi-cup array lifting sheet steel, where the 0.62 Cv keeps flow losses low across long vacuum lines to the outermost cups.
Connects and vents a vacuum reservoir on a leak-test rig wired at AC24V, with the flying lead terminating straight at the bench controller.
Nothing in the 3-port range sits above the 3V3 on flow, so sizing means stepping down when Cv 0.62 is more than needed: to a 3V2 (1/8 or 1/4 port, Cv 0.18-0.19, also vacuum-rated), to a 3V2M (Cv 0.1) when a compact multi-station manifold matters more than flow, or to a 3V1 for the smallest low-power jobs (3.0 W on DC24V). Before ordering, settle five things: port and thread (NPT on this code), initial state (this code is NO), coil voltage (AC24V), electrical entry (flying lead here; remove the I for a DIN plug), and whether the duty includes vacuum — this body does. For double-acting cylinders, go to the 4V series.
Confirm before you order
Flow coefficient Cv 0.62, pressure range 0-0.8 MPa, vacuum rating -102.2 kPa to 0.1 MPa, temperature -20 to 70 C, 10 VA on the AC24V coil (DC builds of this family take 6.5 W), IP65 protection to DIN 40050, 1/4 inch NPT port, 3/2-way normally open function.
Pick NO when the outlet must stay fed — or the vacuum cup must stay loaded — while the coil is off, so a power failure leaves the process in its running state; energising then stops the flow and vents. Pick NC when the outlet must be dead until the coil energises. Both states are orderable in the 3V3 family.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.