
The AirTAC 3V3 Solenoid Valve 3V308NOFIT is a genuine 3-port 2-position (3/2) solenoid valve with 1/4 in ports. It either feeds its outlet or vents it to exhaust, which is what makes it the valve for single-acting cylinders, on/off air blow, clamping, vacuum switching and pilot duty.
On 3V308NOFIT the wiring is built in: instead of a DIN socket, the DC12V coil carries a pre-fitted flying lead, so the valve wires straight into a low-voltage harness with no separate connector to order - a practical advantage on mobile plant, battery carts and 12 V control panels. Functionally it is the same normally open, direct-acting, single-solenoid core with spring return: the outlet is fed until energised, then vented to exhaust.
Flow is the reason to pick the 3V3 body at all. Cv 0.62 is the highest figure in the AirTAC 3-port range, against Cv 0.18-0.19 for 3V2 and Cv 0.1 for 3V2M - a genuine step up rather than a marginal one. The coaxial poppet seals across 0-0.8 MPa and is rated down to -102.2 kPa for vacuum service. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes.
| Model | Airtac 3V3 Solenoid Valve 3V308NOFIT |
|---|---|
| Series | 3V3 |
| Valve type | 3/2-way (3-port, 2-position) |
| Function | Direct-acting, single solenoid, spring return |
| Initial state | Normally open |
| Port size | 1/4 in |
| Thread | NPT |
| Coil voltage | DC12V |
|---|---|
| Electrical entry | Flying lead (lead-out wire type) |
| Coil power | 6.5 W |
| Operating pressure | 0-0.8 MPa (0-114 psi) |
| Vacuum service | Rated -102.2 kPa to 0.1 MPa |
| Flow coefficient | Cv 0.62 |
| Temperature | -20 to 70 C |
| Construction | Coaxial shut-off (poppet), direct-acting, spring return |
| Protection | IP65 (DIN 40050) |
| Medium | Air, filtered by a 40 µm or finer element. Lubrication not required. |
Figures follow the official AirTAC 3V3 catalogue. Confirm coil voltage and thread (PT / NPT / G) against the product label before wiring.
| 3V3 | Body — sets the flow, the coil power and whether vacuum is rated. |
|---|---|
| 1/4 in | Port size. M5, 06 = 1/8 in, 08 = 1/4 in, 10 = 3/8 in. |
| NO | Normally open: air passes until the coil is energised. |
| DC12V | Coil voltage. A = AC220V, B = DC24V, C = AC110V, E = AC24V, F = DC12V. |
| I | Electrical entry: I = flying lead, otherwise a DIN plug. |
| NPT | Port thread. PT is standard; G and NPT are available to order. |
A 3/2 valve has three ports — supply, outlet and exhaust — and two states. It either feeds the outlet or vents it to exhaust, and that is the whole job.
That makes it the right valve for a single-acting (spring-return) cylinder, on/off air blow, a clamp, switching a vacuum generator or suction cup, and piloting a larger valve.
It cannot run a double-acting cylinder. A double-acting cylinder needs air alternately on two sides, which takes a 5-port valve — the AirTAC 4V series.
On utility vehicles, service carts and trailer-mounted kit, the flying lead connects the DC12V coil directly to the battery-fed harness with no DIN connector to source. The normally open state keeps pneumatic tool circuits alive until the operator energises the valve.
Use the 3V308NOFIT as the pilot stage on the actuator of a bigger diaphragm or angle-seat process valve. Cv 0.62 fills the actuator chamber fast for crisp stroking, the 6.5 W coil suits solar- or battery-backed panels, and normally open behaviour fails with air flowing to the pilot.
Bottle-rinse and purge nozzles benefit from NO logic: purge air keeps flowing whenever line control power drops, protecting product hygiene, and the coil is energised only to stop the flow during changeovers. The high flow of the 3V3 body keeps the purge header up to pressure.
The 3V3 body has no larger sibling, so sizing moves only go downward: choose 3V2 (Cv 0.18-0.19, vacuum-rated like this valve) when the full Cv 0.62 is overkill, 3V2M (Cv 0.1) when a compact multi-station manifold beats raw flow, or 3V1 for the lowest-power duties - its DC24V coil needs just 3.0 W. This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. Note that 3V1 carries no vacuum rating, while this body is rated to -102.2 kPa. For double-acting cylinder control, specify the 5-port AirTAC 4V series.
Confirm before you order
3/2-way, direct-acting, single solenoid with spring return; Cv 0.62 flow coefficient; 0-0.8 MPa working pressure plus a -102.2 kPa to 0.1 MPa vacuum rating; -20 to 70 C media temperature; DC12V coil at 6.5 W; IP65 to DIN 40050; This order code has NPT ports (the T in the code); the PT and G versions are separate order codes. air filtered to 40 um or finer, no lubrication needed. There is no published effective-area, response-time or weight figure for this body - request the datasheet if you need them.
3V3 is the largest 3-port body AirTAC makes: Cv 0.62 against Cv 0.18-0.19 for 3V2 and Cv 0.1 for 3V2M, so moving up from a 3V2 is a real jump in flow. Both 3V2 and 3V3 are vacuum-rated; 3V2M and 3V1 are not. Because a 3/2 valve only feeds or vents one line, this model suits single-acting (spring-return) cylinders, blow-off, clamping, vacuum switching and pilot duty. It cannot drive a double-acting cylinder - that calls for the 5-port AirTAC 4V range.
T selects NPT port threads, the North American taper pipe standard. Without it the same order code has PT (Rc) ports, and with G it has G (BSPP) ports; body, function and dimensions do not change.
Genuine AirTAC parts produced by the AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity, coil voltage and destination. We confirm price, availability and lead time — usually within 7 hours.