
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X110-10B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 110mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X110-10B is a double acting, adjustable-stroke compact cylinder built to ISO 21287. The -10 code adds an external stop screw that trims the extend stroke on site anywhere within a 10 mm window, so the usable extend range is 100-110 mm without swapping the cylinder. The hard-anodized aluminium body with a 25 mm S45C hard-chrome-plated rod keeps the whole package short: it saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters when a 110 mm stroke must fit inside a guarded press frame or a heavy welding fixture.
The fixed TPU bumper at both ends absorbs end-of-stroke energy, and speed runs 30-500 mm/s over 0.15-1.0 MPa (22-145 psi) of clean, 40 um filtered air. Mounting hardware - FA flange, LB foot, FTC brackets and I/Y rod knuckles - bolts straight to the ISO 21287 face. This unit has a male rod thread (B code) and a 1/4" PT port; no magnet is fitted, so order the -S variant if CMSE / DMSE switch sensing is needed later.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X110-10B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 110 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×110 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The male rod thread and about 188 kg vertical-lift margin let this cylinder pull heavy weld clamps or lift-and-locate units in automotive body shops, with the stop screw dialling the stroke in after setup.
In warehouse tooling, the 5890.5 N pull at 0.5 MPa retracts heavy pushers and die-change drawers, and the short ISO 21287 body fits where a full-length profile cylinder would not.
At this bore size the ACEJ125X110-10B sits at the top of the range: the next step down, the 100 mm bore, pushes 3927 N at 0.5 MPa, so choose the 125 mm only when your tooling genuinely needs the extra 6135.9 N. If the load is lighter, the 100 mm bore saves cost and air. Remember the stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock - on air loss the piston still drifts, so add a separate valve or clamp if the position must hold. The male rod thread suits direct bolting into press platens and weld guns, and the 10 mm window covers final trim after fixture commissioning.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
It is double acting with an adjustable extend stroke: the -10 stop screw trims the 110 mm stroke by up to 10 mm, giving a 100-110 mm range. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, port 1/4" PT, rod 25 mm with male thread.
The ISO 21287 short-body design saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into tight press frames and fixtures. A fixed TPU bumper at each end absorbs end-of-stroke energy. Sensing is not fitted on this model: the magnet is the optional -S code, which enables CMSE / DMSE reed or solid-state switches on the body's magnet slots. FA flange, LB foot, FTC brackets and I/Y rod knuckles mount directly to the ISO 21287 face.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.