
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X120-40B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 120mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X120-40B is a double acting ISO 21287 compact cylinder with a 125 mm bore and a 120 mm stroke that an external stop screw trims on site by up to 40 mm, giving a usable extend range of 80-120 mm. At 0.5 MPa it pushes with 6135.9 N and pulls with 5890.5 N, rising to 8590.3 N on the extend side at 0.7 MPa - heavy-press territory. The B code gives a male rod thread on the 25 mm rod, and the 1/4" port feeds the large bore quickly enough to hold the 30-500 mm/s speed band.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so a 125 mm bore fits presses and clamping fixtures that were previously too tight for this force class. A fixed TPU bumper at each end absorbs end-of-stroke energy, the hard-anodized aluminium body resists wear, and the optional -S magnet enables CMSE / DMSE switches if position feedback is added later.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X120-40B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 120 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×120 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The 25 mm male-thread rod swings heavy pallet-line gates and stops; the short body mounts where a full-length profile cylinder cannot, and the 1/4" port cycles the big bore at up to 500 mm/s.
Mould-change slides need repeatable clamping position: the stop screw trims the extend stroke in the 80-120 mm range, the fixed TPU bumper softens each end, and FA flange mounting bolts straight to the mould plate.
The 120 mm stroke sits well inside the 300 mm maximum standard stroke for this bore, so it is a catalogue item, not a made-to-order build. Remember the -40 adjuster is a mechanical end stop for the extend stroke only: it sets where the rod stops, but on air loss the piston still drifts, so add a separate locking solution if a load must be held mid-stroke. FA flange or LB foot mounting bolts to the ISO 21287 face, and if you need switch feedback, order the -S version because this model has no magnet fitted.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa push rises to 8590.3 N and pull to 8246.7 N, with a theoretical maximum of 1251.4 kgf at 1.0 MPa. The -40 code is a 40 mm adjustment window: an external stop screw shortens the 120 mm extend stroke on site, so the usable range is 80-120 mm. It cannot lengthen the stroke past 120 mm, and the stop is not a mid-stroke lock - on air loss the piston still drifts. Operating pressure is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, and the 25 mm rod carries a male thread from the B code.
It is an ISO 21287 compact cylinder whose hard-anodized aluminium body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so a 125 mm bore fits tight press frames and gantries. A fixed TPU bumper at each end absorbs end-of-stroke energy. FA flange and LB foot mounts bolt to the standard ISO 21287 face. This model has no magnet fitted; the optional -S magnet enables CMSE / DMSE reed or solid-state switches, so order that code if you need end-position sensing.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.