
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X160-10B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 160mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
An external stop screw trims the extend stroke anywhere within the ordered 10 mm window, so the effective range is 150-160 mm, set with a screwdriver right on the machine. The male rod thread (B code) bolts straight to your tooling.
The hard-anodized aluminium body with an S45C hard-chrome-plated 25 mm rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters when a 160 mm stroke must fit inside a press frame or weld fixture. Fixed TPU bumpers absorb end-of-stroke shock, speed spans 30-500 mm/s, and pressure runs 0.15-1.0 MPa (22-145 psi).
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X160-10B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 160 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×160 | Stroke length in mm. |
| -10 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
In a sand-casting line the male-thread 25 mm rod drives a mould close-out slide where the short ISO 21287 body fits between jacket walls a full-length cylinder cannot.
If 6135.9 N is far more than needed, the 80 mm bore (2513.3 N) saves air and cost. Remember the stop screw is a mechanical end stop for the extend stroke, not a mid-stroke lock: on air loss the piston still drifts, so add a separate holding valve for suspended loads. Mount with FA flange or LB foot on the ISO 21287 face; the magnet is not fitted on this code, so order the -S variant if you later need CMSE / DMSE switch feedback.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
Push is 6135.9 N and pull 5890.5 N at 0.5 MPa; at 0.7 MPa push reaches 8590.3 N, with a theoretical maximum of 1251.4 kgf at 1.0 MPa. It is double acting with an adjustable extend stroke (10 mm window, usable 150-160 mm), 1/4" PT ports, a 25 mm male-thread rod, speed 30-500 mm/s, pressure 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), and -20 to +70 C operation on air filtered to 40 um.
The ISO 21287 short body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so it slots into deep dies and guarded frames. Fixed TPU bumpers at both ends absorb end-of-stroke impact. This code has no magnet fitted; order the optional -S version to enable CMSE / DMSE reed or solid-state switches, and bolt on FA flange or LB foot mounting from the standard ISO 21287 face.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.