
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X200-40B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 200mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X200-40B is a double acting ISO 21287 compact cylinder with a 125 mm bore and a 200 mm stroke that an external stop screw trims by up to 40 mm, giving a usable extend range of 160-200 mm. At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N, rising to 8590.3 N on the extend stroke at 0.7 MPa. The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so this heavy-thrust actuator still fits presses, gantries and guarding where a full-length body will not.
The hard-anodized aluminium body carries a 25 mm S45C hard-chrome rod with a male thread (B code), the 1/4" PT ports depend only on the bore, and a fixed TPU bumper at each end absorbs end-of-stroke energy. The optional -S magnet enables CMSE / DMSE switches; without it no sensor can be fitted.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X200-40B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 200 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×200 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The 6135.9 N extend force at 0.5 MPa crushes scrap, cartons or offcuts in a recycling cell, with the 40 mm window letting operators trim the ram stroke to match different bin depths.
A 125 mm bore clamps stacked pallet loads before wrapping; the short ISO 21287 body tucks under low guarding, and the male rod thread suits a fabricated clamp arm.
Clamping a cast-iron housing against a milling fixture needs about 375 kg of usable force at 0.5 MPa; the stop screw sets the clamp stroke once and holds it there batch after batch.
Choose the -40 window when the tooling stroke must be set on site anywhere between 160 and 200 mm; the stop screw shortens the extend stroke only and never lengthens it past 200 mm. Remember the adjuster is a mechanical end stop, not a mid-stroke lock: on air loss the piston still drifts, so add a separate holding valve for suspended loads. Bolt FA flange or LB foot mounts to the ISO 21287 face, and order the -S code if CMSE / DMSE position sensing is needed.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa the push is 8590.3 N and the pull 8246.7 N, with a theoretical maximum of 1251.4 kgf at 1.0 MPa. The -40 code gives a 40 mm adjustment window: a stop screw shortens the 200 mm extend stroke to any length from 160 to 200 mm. It shortens only - it cannot extend past 200 mm - and it is an end stop, not a load-holding brake. Operating range is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, air filtered to 40 um.
It is an ISO 21287 compact cylinder: hard-anodized aluminium body with a roller-burnished bore, threaded aluminium covers, a 25 mm S45C hard-chrome rod with male thread, and a fixed TPU bumper at each end that decelerates the piston at the ends of travel. The body saves about 50% of the mounting length of an ISO 15552 profile cylinder. FA flange and LB foot mounts plus I/Y rod knuckles bolt to the standard face. Position sensing requires the optional -S magnet code; this model has no magnet, so CMSE / DMSE switches cannot be used unless -S is ordered.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.