
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X40-40B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 40mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder with an adjustable extend stroke, the ACEJ125X40-40B pairs a 125 mm bore with a 40 mm stroke and a male-threaded 25 mm rod (the B code). At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa push rises to 8590.3 N, with a theoretical ceiling of 1251.4 kgf at 1.0 MPa. The external stop screw trims the extend stroke anywhere inside the ordered 40 mm window, so one cylinder serves several die or fixture positions. Air supply is 0.15-1.0 MPa (22-145 psi), speed 30-500 mm/s, and a fixed TPU bumper sits at each end.
The hard-anodized aluminium body with an S45C hard-chrome rod saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters when a 12-tonne-class press fit or clamp must fit inside a guarded gantry. Plan on roughly 3682 N (about 375 kgf) of real work at 0.5 MPa rather than the full rating; halving the vertical-lift equivalent of 625 kg gives about 312 kg as a conservative lifting figure. Note the stop screw is a mechanical end stop only - on air loss the piston drifts, so it never holds a load. FA/LB mounting and I/Y rod knuckles bolt to the standard ISO 21287 face; the optional -S magnet enables CMSE / DMSE switches and is not fitted on this code.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X40-40B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 40 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×40 | Stroke length in mm. |
| -40 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Short-stroke pressing of bearings into housing bores on an automotive line, where 6135.9 N at 0.5 MPa is enough and the 40 mm window lets one cylinder serve two part variants.
Clamping large castings against hard stops in a CNC fixture; the compact body fits where an ISO 15552 profile cylinder would be about twice as long.
Locating and lifting die-set pins of roughly 300 kg in a stamping shop, using the conservative half-margin vertical figure derived from the 0.5 MPa push force.
The -40 window means the 40 mm extend stroke can be shortened on site down to nearly zero, but it cannot be lengthened past 40 mm - order a longer stroke if in doubt. This code has no magnet: add -S if CMSE / DMSE position switches are planned. Choose FA flange or LB foot to match the fixture, and the B male rod thread for direct knuckle attachment.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
Push is 6135.9 N and pull 5890.5 N at 0.5 MPa; at 0.7 MPa push is 8590.3 N and pull 8246.7 N; theoretical maximum is 1251.4 kgf at 1.0 MPa. The -40 code gives a 40 mm adjustment window: an external stop screw shortens the 40 mm extend stroke on site within that range. It is a mechanical end stop, not a load lock - on air loss the piston still drifts. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof 1.5 MPa (215 psi), speed 30-500 mm/s, with a fixed TPU bumper at both ends.
The hard-anodized aluminium body on the ISO 21287 footprint saves about 50% of the mounting length of an ISO 15552 profile cylinder, with a 25 mm hard-chrome S45C rod and a 1/4" PT port. This code has no magnet, so no CMSE / DMSE switch can be read - order the optional -S magnet version if sensing is needed. FA flange and LB foot mount to the standard face, and I or Y rod knuckles suit the B male thread. For longer travel, standard strokes run to 300 mm on this bore.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.