
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X55-30B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 55mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
A double acting ISO 21287 compact cylinder, the ACEJ125X55-30B pairs a 125 mm bore with a 55 mm stroke that an external stop screw trims by up to 30 mm on site, giving a usable extend range of 25-55 mm. At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N, so a 0.6 rule of thumb leaves roughly 3680 N of real work force. The hard-anodized aluminium body and S45C hard-chrome plated 25 mm rod stand up to high-cycle press and clamping duty.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, which matters when a 300 mm-class bore must fit inside a press frame or weld fixture. A fixed TPU bumper at each end absorbs end-of-stroke energy, and speeds of 30-500 mm/s cover both slow pressing and fast ejection. Note the stop screw is a mechanical end stop only: on air loss the piston still drifts, so it is not a load-holding brake.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X55-30B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 55 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×55 | Stroke length in mm. |
| -30 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
The short ISO 21287 body slots into tight mould-carrier frames where a full-length ISO 15552 profile cylinder would not fit, with 6135.9 N holding force at 0.5 MPa.
If your job needs position feedback, order the -S variant with the optional magnet for CMSE / DMSE switches; this B-code unit has no magnet fitted. The male rod thread (B code) suits rod couplers and knuckles, and FA flange or LB foot mounts bolt to the ISO 21287 face. Standard strokes for bore 125 run to 300 mm, so 55 mm is well inside the catalogue range.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa push rises to 8590.3 N and pull to 8246.7 N, with a theoretical maximum of 1251.4 kgf at 1.0 MPa. The -30 code gives a 30 mm adjustment window, so the 55 mm extend stroke can be trimmed anywhere down to 25 mm via the external stop screw. It runs on air filtered to 40 um at 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), at speeds of 30-500 mm/s and -20 to +70 C.
The ISO 21287 compact body is hard-anodized aluminium with threaded aluminium covers, a hard-chrome plated S45C rod, and fixed TPU bumpers at both ends; it is about 50% shorter in mounting length than an ISO 15552 profile cylinder. This unit has a male rod thread and 1/4" PT ports. Switches need the optional -S magnet code, which enables CMSE / DMSE reed or solid-state switches; without -S no magnet is fitted. FA flange and LB foot mounts plus I/Y rod knuckles bolt straight to the standard face.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.