
The AirTAC ACEJ125 Adjustable Compact Cylinder ACEJ125X70-20B is a genuine double acting, double rod, adjustable stroke ISO 21287 compact air cylinder with a Ø125mm bore and 70mm stroke, 1/4" air ports and a hard-anodized aluminium body. Its short compact envelope saves about 50% of the mounting length of an ISO 15552 profile cylinder.
The ACEJ125X70-20B is a double acting, adjustable-stroke compact cylinder built to ISO 21287. The -20 code adds an external stop screw that trims the 70 mm extend stroke by up to 20 mm on site, giving a usable range of 50-70 mm without swapping the cylinder. The B code specifies a male rod thread on the 25 mm rod, and the air port is 1/4" PT.
The short ISO 21287 body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so this force class fits inside presses, weld fixtures and gantries that cannot accept a full-length body. A hard-anodized aluminium body with a hard-chrome plated S45C rod resists wear, and fixed TPU bumpers at both ends absorb end-of-stroke shock. Note the stop screw is a mechanical end stop only: on air loss the piston still drifts, so it is not a load-holding brake.
| Model | Airtac ACEJ125 Adjustable Compact Cylinder ACEJ125X70-20B |
|---|---|
| Series | ACEJ compact cylinder |
| Standard | ISO 21287 |
| Bore size | Ø125 mm |
| Stroke | 70 mm |
| Acting type | Double acting, double rod, adjustable stroke |
| Port size | 1/4" |
| Rod thread | M16×2.0 |
| Fluid | Air (filtered by 40µm element) |
|---|---|
| Operating pressure | 0.15 – 1.0 MPa |
| Proof pressure | 1.5 MPa |
| Temperature | -20 to +70 °C |
| Speed range | 30 – 500 mm/s |
| Cushion | Fixed TPU bumper (both ends) |
| Max standard stroke | Up to 300 mm |
Specifications follow the official AirTAC ACE-series (ISO 21287) datasheet. Body: hard-anodized aluminium alloy; piston rod: S45C carbon steel with hard-chrome plating. Rod type: female thread (blank) or male thread (B). Thread options: PT (blank) / G. A built-in magnet is OPTIONAL — add the -S code to fit CMSE / DMSE position sensors.
| Pressure | Force (both ways) |
|---|---|
| 0.5 MPa | 5890 N |
| 0.7 MPa | 8247 N |
| Max (@1.0 MPa) | 1201 kgf |
ACEJ is double-rod: the rear rod that carries the stroke adjuster exits the rear cover, so both piston faces lose rod area. The rod-side (annular) area is used for both directions (conservative).
| ACEJ | ISO 21287 compact cylinder (adjustable-stroke). |
|---|---|
| 125 | Bore size in mm. |
| ×70 | Stroke length in mm. |
| -20 | Adjustable stroke window (mm the extend stroke can be shortened on site). |
| S | Optional built-in magnet for CMSE / DMSE sensors (omit for no magnet). |
| B | Rod type: B = male thread; blank = female thread. |
ACE-family variants: ACE (double acting), ASE / ATE (single acting push / pull), ACED (double rod), ACEJ (double rod, adjustable stroke), TACE / TACED (non-rotating twin-guide yoke). Mounting accessories: FA / FB flange, LB foot, CA / CB clevis, CR, SDB pivot, FTC; plus I and Y knuckles. Thread PT (blank) / G.
Clamps thick steel weldments in automotive jigs where the short ISO 21287 body fits between fixture plates, and the male rod thread takes a Y knuckle for swiveling clamp arms.
If your load needs less than about 4000 N, step down to the 100 mm bore; if you need the full 1251.4 kgf theoretical maximum at 1.0 MPa, stay at 125 mm. The 20 mm window suits fixed tooling where the stroke must be fine-tuned after installation - it shortens the extend stroke only, never lengthens it past 70 mm.
This unit has no magnet fitted, so no CMSE or DMSE switch can be used; order the -S version if position sensing is required. Mounting: FA flange or LB foot bolt to the ISO 21287 face, with I and Y rod knuckles on the male threaded rod. Speed range 30-500 mm/s, air filtered to 40 um, 0.15-1.0 MPa (22-145 psi) operating pressure.
AirtacDistr lists every ACEJ125 order code with its price on one page at https://airtacdistr.com/products/airtac-acej125-adjustable-double-rod-compact-cylinder
Quick checklist
At 0.5 MPa it pushes 6135.9 N and pulls 5890.5 N; at 0.7 MPa push is 8590.3 N and pull 8246.7 N, with a theoretical maximum of 1251.4 kgf at 1.0 MPa. The -20 code is a 20 mm adjustment window: an external stop screw shortens the 70 mm extend stroke by up to 20 mm, giving 50-70 mm of usable travel. It is a mechanical end stop, not a mid-stroke lock - on air loss the piston still drifts. Operating pressure is 0.15-1.0 MPa (22-145 psi), proof pressure 1.5 MPa (215 psi), speed 30-500 mm/s, temperature -20 to +70 C, and the port is 1/4" PT on a 25 mm male-threaded rod.
The ISO 21287 compact body saves about 50% of the mounting length of an ISO 15552 profile cylinder, so a 125 mm bore fits where a full-length profile cylinder will not. Fixed TPU bumpers at both ends absorb end-of-stroke impact. This model has no magnet, so no switch can be mounted; order the -S code to enable CMSE or DMSE switches. FA flange and LB foot mountings bolt straight to the ISO 21287 face, and I or Y rod knuckles suit the male rod thread. Outline dimensions: confirm from datasheet.
Genuine AirTAC parts produced by AirTAC factory.
Covers non-human-caused product damage.
Most standard models are dispatched in 3-5 days.
Most inquiries answered within 7 hours.
Send us the quantity and destination. We confirm price, availability and lead time — usually within 7 hours.